我都加入了DB01行列

各位師兄, 多多指教!

[ 本帖最後由 t2 於 2009-3-14 21:02 編輯 ]

想請教各位, 有D咩parts要買定(有d咩易爛)?  因為我係4wd buggy新手.

D arms易爛!!

原帖由 matlc1234 於 2009-3-11 19:56 發表

                               
登錄/註冊後可看大圖

D arms易爛!!

多謝師兄!  請問用TRF 501x既arm 會好d 嗎?

原帖由 t2 於 2009-3-11 07:59 PM 發表

                               
登錄/註冊後可看大圖

多謝師兄!  請問用TRF 501x既arm 會好d 嗎?

sure la !
nice paint job , done by yourself ??

原帖由 Evo5 於 2009-3-11 20:28 發表

                               
登錄/註冊後可看大圖

sure la !
nice paint job , done by yourself ??

Thanks.  係呀, 自己噴既.  風翼仍在上色中.

原帖由 t2 於 2009-3-11 19:47 發表

                               
登錄/註冊後可看大圖

想請教各位, 有D咩parts要買定(有d咩易爛)?  因為我係4wd buggy新手.

Hi c hing nice car, keep an eye on your rear diff, it can break very easily

個殼噴得好靚正

原帖由 Eddie168 於 2009-3-11 21:53 發表

                               
登錄/註冊後可看大圖

Hi c hing nice car, keep an eye on your rear diff, it can break very easily

吓, 咁請問有咩放法令佢耐用d呀?  部車要整rear diff都要鬆好多鏍絲喎!  

原帖由 Marco明 於 2009-3-11 21:59 發表

                               
登錄/註冊後可看大圖

個殼噴得好靚正

多謝.   其實噴Buggy殼我都係第二次, 希望下次再噴好d.

原帖由 t2 於 2009-3-11 22:00 發表

                               
登錄/註冊後可看大圖

吓, 咁請問有咩放法令佢耐用d呀?  部車要整rear diff都要鬆好多鏍絲喎!  

Make sure the diff is not too tight and is not slipping otherwise the glue between the diff plate and the plastic plate holder will split and will slip against each other (this is fine if you're running a mild motor but im not sure what motor you're running in the picture) and therefore the plate will generate heat and melt the pulley, i would reccomend replace the orginal ones by a TRF501x diff halves as they are straight swap and bullet proof

Here is my way to build my diff and i have never had any problems with my diff before so you might want to have a look at this http://bbs.rc-evo.com/viewthread ... &extra=page%3D2 (This is just my opinion and cannot 100% guarantee it will work everytime) hope this helps

原帖由 Eddie168 於 2009-3-12 01:45 發表

                               
登錄/註冊後可看大圖

Make sure the diff is not too tight and is not slipping otherwise the glue between the diff plate and the plastic plate holder will split and will slip against each other (this is fine if you're r ...

Thanks a lot.  

I'll buy the 501x diff joints shortly and use them to rebuild the diff.

原帖由 t2 於 2009-3-12 06:46 發表

                               
登錄/註冊後可看大圖

Thanks a lot.  

I'll buy the 501x diff joints shortly and use them to rebuild the diff.

Also the Suspension blocks (part A12) and the suspension ball (part A2) are weak points of the car and it's a good idea to replace them with metal ones as they tend to break quite easily if you crash as much as me but it is not necessary

by the way very nice shell and where do you play??

Other than A arms, there is also stock support for front and rear.  (backup parts incase of Cup 4)  Really nice paint job.

原帖由 Eddie168 於 2009-3-12 08:57 發表

                               
登錄/註冊後可看大圖

Also the Suspension blocks (part A12) and the suspension ball (part A2) are weak points of the car and it's a good idea to replace them with metal ones as they tend to break quite easily if you cr ...

Thanks for your advice.  I've changed the suspension ball to metal one but the blocks are still the stock items come with the car.  Need to spend money again!

Most likely I'll play it at TRC later (after getting the necessary parts of course).

原帖由 mlee 於 2009-3-12 12:17 發表

                               
登錄/註冊後可看大圖

Other than A arms, there is also stock support for front and rear.  (backup parts incase of Cup 4)  Really nice paint job.

Are u talking about the shock tower (M parts)?  I've changed them to carbon reinforced ones, hopefully to be stronger (I guess).

When the car (Cup 4), the car tends to "rub ginger" against the floor so it does not matter if it is carbon re-inforced or carbon fibered, the end result will be the same.  Just to be good to have this spare part.

原帖由 mlee 於 2009-3-12 15:30 發表

                               
登錄/註冊後可看大圖

When the car (Cup 4), the car tends to "rub ginger" against the floor so it does not matter if it is carbon re-inforced or carbon fibered, the end result will be the same.  Just to be good to have thi ...

Thanks 師兄.

風翼上色都完成啦.

DB-01 MS 花

原帖由 Marco明 於 2009-3-12 18:06 發表

                               
登錄/註冊後可看大圖

DB-01 MS 花

希望星星真係會出架DB01 MS就正啦!