又話ad stock motor 唔哂加fet ge??!

如題~點解我一用ad stock motor..個pcb就燒左!_!....唉....

好多舊 post 都話 AD 要加 fet.......

如題~點解我一用ad stock motor..個pcb就燒左!_!....唉....
山久和也 發表於 2009-8-26 22:45

                               
登錄/註冊後可看大圖

我買左都唔用,玩過兩次勁熱停左係度~真係唔感再用~

AD Stock On AWD ?

Since the original Design of AD Stock is for MR-02 ,
Maybe because you use on AWD , So the loading increased ,
so the PCB may not support with : AWD+AD Stock , But MR-02+AD Stock
And one more reason is that , the Gear Ratio is too low on your car ,
make the loading increased too !

我架係MR02-.-用到出哂煙-.-

我架係MR02-.-用到出哂煙-.-
山久和也 發表於 2009-8-27 00:34

                               
登錄/註冊後可看大圖

Did you check other part of the car.....like the wire.....any wire touch together?

AD stock, 係 2.4G板先唔使加FET wor
我用 AD stock 係 2.4G mr02, 用 9T 玩左半年都無事

AD stock, 係 2.4G板先唔使加FET wor
我用 AD stock 係 2.4G mr02, 用 9T 玩左半年都無事
800mah 發表於 2009-8-27 01:51

                               
登錄/註冊後可看大圖

AD PCB should be OK too!

AD stock, 係 2.4G板先唔使加FET wor
我用 AD stock 係 2.4G mr02, 用 9T 玩左半年都無事
800mah 發表於 2009-8-27 01:51

                               
登錄/註冊後可看大圖

但係我都係2.4~都一樣熱到停左~

但係我都係2.4~都一樣熱到停左~
阿業阿業 發表於 2009-8-27 02:15

                               
登錄/註冊後可看大圖

But your PCB is ok now or not??

當年為左用AD STOCK~~~係咁銲4562FET~~

AWD 2.4g如果唔加fet可以用到atomic既咩motor??awd stock??? ad stock??? stock r???

ad stock....... stock r.......is ok.......

AWD 2.4g如果唔加fet可以用到atomic既咩motor??awd stock??? ad stock??? stock r???
free14hk 發表於 2009-8-27 03:05

                               
登錄/註冊後可看大圖

你要玩快motor就最好疊埋FET, 如果唔係又要用齒比就，又話唔用得呢隻motor果隻motor...
玩快motor但唔玩得最快果隻，為咩呢？
根本加FET就係改善PCB既輸出，又可以唔使就住就住玩咩motor，點解唔加呢？
另外，如果你真係想節省少少金錢，唔加玩快motor，到頭來燒FET，咪一樣要俾錢加
最最重要係，人地話呢隻motor又快又唔使加FET，你係咪試丫？
人地係屋企玩，我地係車場玩，你都係會上黎車場玩，點解我地個個都加，我地唔想玩平D？
另外，加FET係唔使$300咁貴，你再打下價啦
最後，一係你玩原裝設計既野，所有手繞，atomic,PN...站係kyosho立場全部都唔合乎佢塊PCB既設計，壞係正常，無問題係慶幸你塊PCB體質好
玩得非原裝快摩打就要加FET，否則可以選擇xpeed
多D上黎玩下車，吹下水啦~~

11# scalpel


NO!_!

15# henry888


C兄你講得岩~~點都要加FET..即使玩普遍MOTOR又好..玩快MOTOR都好~隨時都用得..都係加左先@@~~請問各位C兄D FET幾$粒同用邊隻~?!

Normally CHing,
I want to know too.
Which shops have good workmanship?
How many FET you add? (Model "8...p" something)
How much will be?
Thx.

Normally CHing,
I want to know too.
Which shops have good workmanship?
How many FET you add? (Model "8...p" something)
How much will be?
Thx.
Carsong 發表於 2009-8-27 11:03

                               
登錄/註冊後可看大圖

Both CT and MMS have good workmanship........About $30 each FET......SP8M4!

How many FET you add normally?
Thx.