吾識用辣雞!!!!

吾識辣..................

可5可以幫幫手
thx

點唔識
插電>等佢熱>雞頭同件分別先上鍚>雞頭同工件成45度角落鍚辣落工件>搞掂



可以點唔識用?

你係咪想焊 T 插.... ?

This link can help you --> www.youtube.com/watch?v=BLfXXRfRIzY
Then practice, practice and practice. Too simple.
Good Luck!

ok thx~~

點唔識
插電>等佢熱>雞頭同件分別先上鍚>雞頭同工件成45度角落鍚辣落工件>搞掂



可以點唔識用?
Noir.KAZE 發表於 2009-7-9 12:13

                               
登錄/註冊後可看大圖

You almost answer his question, I bet he also know the procedure. He just lack of confident and want to see the steps by sight. YouTube fixed this issue!!

你點唔識焊呀??T插??..我又會用D令D鍚線..街邊一筒幾蚊唔好買..超垃圾...
好易JA啵...^^學多D就會識..
玩車一定要識...焊野..我會整濕布係側邊抺一抺雞頭

You almost answer his question, I bet he also know the procedure. He just lack of confident and want to see the steps by sight. YouTube fixed this issue!!
yakuza 發表於 2009-7-9 12:33

                               
登錄/註冊後可看大圖

最緊要係唔好心急同要注意安全,辣到一下真係痛到嘔.......

想問下係用支雞熱d錫,定係用支雞去熱件部件先再落錫?

如果熱部件先,你部件如果係t插,d膠會熔,先在鐵片上錫,之後把帶有鍚的雞頭壓在電線上重覆一直做直到條電線ga金屬部份充滿鍚,之後熱番鐵片上面d錫,放條電線上去,finish,套番熱縮膠

想問下係用支雞熱d錫,定係用支雞去熱件部件先再落錫?
一匹狼 發表於 2009-7-9 14:01

                               
登錄/註冊後可看大圖

第一果個係用黎預焊
通常d錫好快就會溶落個工件上面
第2果個就係焊埋兩件野果陣先將預焊既料熱返溶佢,咁焊既時候就會比較容易,但係係雞頭埋位就要落錫
呢個係我既做法,其他師兄可能唔係咁做

http://hk.f1.page.auctions.yahoo.com/hk/auction/1117577577
http://hk.f1.page.auctions.yahoo.com/hk/auction/1117910633
http://hk.f1.page.auctions.yahoo.com/hk/auction/1119266390

呢set野o吾ok?

支雞要用到M先夠力,應該都ok既
值唔值就唔知啦,但係呢d野可以既話買d質量高d既會好d
因為好多時都會用到

先搽小小松香膏係接頭同電線到然後上錫,0甘就好易焊,同埋好實淨．

你想點幫?   

買D 鍚有埋松香咪得囉....好易上

最緊要係唔好心急同要注意安全,辣到一下真係痛到嘔.......
Noir.KAZE 發表於 2009-7-9 13:17

                               
登錄/註冊後可看大圖

Ya!!!Before i was心急,so  辣到真係痛到嘔!!! 痛3-4HRS!!