TA05-VER.2 行唔到直

小弟新手剛入了一部TA05v2 ,但發現行唔到直,點set都偏左行,右邊用了120g鉛去平衡都係咁. 有無brother都有這個問題,但解決到ga?
本車左邊是放servo,電變和摩打.右邊是放5200鋰電.setting跟manual一樣.

在TRC場裏用咗tire水都係好難行直.

用120g鉛去平衡,點分佈先?

我玩IFSR（頭直尾差 ） AND我同事玩TA05 VII （頭尾差），都有呢個問題
後來發覺“好似”係個SERVO 影響

what servo saver did you use ?

排電則埋一邊~ 行唔直好正常

現今＋架房車九架啲電都係放一邊啦...唔通架架都走唔到直線？

現今＋架房車九架啲電都係放一邊啦...唔通架架都走唔到直線？
abba 發表於 2010-7-18 22:37

                               
登錄/註冊後可看大圖

先天性既問題~要靠後天既努力去改正

操多D...你會改善LEE個問題

我都已經用孖星藍色OPTION SERVO SAVER LA.SERVO 用Savox servo, 0.08sec.
其實我支4PK要唔要SET D 野GA?因為我只是SET咗中位.

我都已經用孖星藍色OPTION SERVO SAVER LA.SERVO 用Savox servo, 0.08sec.
其實我支4PK要唔要SET D 野GA?因 ...
mikeywcm 發表於 2010-7-18 23:09

                               
登錄/註冊後可看大圖

可以SET左右CURVE及航程不同~就返部車左右不平衡的先天問題~

我都係用返原裝粒膠...再加”人手”微調，架車先直

要在支控入面SET佢大細軚呀?因為我用微調,調得太右的話,支推桿會'KICK' SERVO呀.

大油行唔直定空油行唔直?

係大油行唔直,令到我係trc大直路兩邊擺.

似係珠差太緊同起油太急,後輪揩呤揩殼彈弓太軟都可能

檢查下車架是否2邊平衡, a臂順唔順, bearing 有無死到, 轉向2邊推銲長度是否一樣等等.............

左右不平衡 has less effect for 行唔直. First thing first, check the front and rear toe in and out.

Trim the front wheel to a straight line first, for 4PK adjust your "subtrim". Don't touch the L, R curve.

In usual case of today car design, if u add 70-120g at battery side, u are not too far from balance.

Here is my "On scale" estimation:
351g Motor side weight = 170g (motor) + 46g (servo 9551) + 15g (reciever 604) + 100g (ESC+wires) 20g (motor heatsink + fan)

280g (5200 lipo)

That's why i added 70g and put the car on 2 balance tools to check. Straight line very good at TRC.

排電則埋一邊~ 行唔直好正常
billgate803 發表於 2010-7-18 22:01

                               
登錄/註冊後可看大圖

do u mean all the T3, 416, BD5, sakura, Photon, TB03, TT01 .... etc = 行唔直好正常

do u mean all the T3, 416, BD5, sakura, Photon, TB03, TT01 .... etc = 行唔直好正常
hk_sdu 發表於 2010-7-19 12:24

                               
登錄/註冊後可看大圖

可以咁講~