RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: tomy intruder [打印本頁]

作者: spoonbb6 時間: 2008-6-27 17:04
標題: tomy intruder
just bought a tomy intruder a few days ago and start the restoration... very difficult..

took me more than 30 mins to clean up one dog bone.....

[ 本帖最後由 spoonbb6 於 2008-6-27 17:07 編輯 ]

作者: tamiyafan 時間: 2008-6-27 22:49
請問師兄用D咩可令生銹或氧化咗既金屬回復光澤?

作者: tiger1 時間: 2008-6-28 23:34
Can c- hing show some more photos of the car. Want to see lah

作者: spoonbb6 時間: 2008-6-30 13:30

原帖由 tamiyafan 於 2008-6-27 22:49 發表

 登錄/註冊後可看大圖

請問師兄用D咩可令生銹或氧化咗既金屬回復光澤?

use 巴素擦銅水.

作者: spoonbb6 時間: 2008-6-30 13:31

原帖由 tiger1 於 2008-6-28 23:34 發表

 登錄/註冊後可看大圖

Can c- hing show some more photos of the car. Want to see lah

spend the week end to clean up. The chassis is clean now.

作者: spoonbb6 時間: 2008-6-30 14:08
hello every one, I am going to work on the wheels and I need some help.

1) the sponge tire is stick on the plastic wheel and very difficult to take it out, any suggestions?
2) the plastic wheel looks pretty bad in shape, is it possible to find a replace for that?

Many thanks!

作者: Evo5 時間: 2008-6-30 14:29
there are no replacement for that , use thinner to take off the tyre

作者: tiger1 時間: 2008-6-30 18:36
Use Yokomo wheels?

Thinner to take off sponge tires.

作者: tiger1 時間: 2008-6-30 18:39
very nic condition chassis wor

作者: ftbingobingo 時間: 2008-6-30 19:17
It is a really great project

作者: spoonbb6 時間: 2008-7-2 10:21
after a hard working july1 public holiday.

作者: mlee 時間: 2008-7-2 11:37
How about the belt and shell? is it still in good shape? Looking really good!

作者: tiger1 時間: 2008-7-3 08:30
Can you show some more of the motor mount? That looks very sweet

作者: minimini 時間: 2008-7-3 12:30
I think the red motor heat-sink is by GPM or some local HK shops......

作者: tiger1 時間: 2008-7-3 13:13
Wish I could have one....

作者: spoonbb6 時間: 2008-7-3 13:42
finally, took the sponge tire out....

going to buy a set of new tire today or tomorrow~~ (along with the DF03-MS)

attached are some motor mount image.

[ 本帖最後由 spoonbb6 於 2008-7-3 16:34 編輯 ]

作者: tiger1 時間: 2008-7-3 20:11
Now, question is: who has a motor mount like this for sale? I really want one now

[ 本帖最後由 tiger1 於 2008-7-4 08:49 編輯 ]

作者: tiger1 時間: 2008-7-6 00:25
If you look into the spec of this car, especially the intruder ex, it is actually very close to our current 2008 buggies. Except there is no slipper clutch, graphite chassis and the batteries are position a bit more laterally than the newer one. In other words, this is almost full spec.

It has aeration shocks just like rc10, nicely machined ball differentials rear and front, belt tension adjuster at the differential, long suspension arms made of solid material, lexam under tray, solid metal motor mount, adjustable rear toe-in, ball bearing steering, universal shafts, center motor mount, very solidly set up suspension mounts, etc..

Looking at the instruction of the car, there is really very little to improve or modify. It is actually hard to find flaw to modify further.

[ 本帖最後由 tiger1 於 2008-7-6 00:29 編輯 ]

作者: tiger1 時間: 2008-7-6 00:28
Motor mount may be the only area to improve because it was made of cast alloy, which is a little more brittle than machine aluminium alloy. However, being cast alloy motor mount, it works as a heat sink already, not perfect, but very close from a functional point of view. Also, the quality of the motor mount casting was EXCELLENT!!

作者: tiger1 時間: 2008-7-6 00:30
If I were Tomy, I would also get bored with 1/10 scale buggies since a close to perfect car has been made...

作者: minimini 時間: 2008-7-6 00:33

原帖由 tiger1 於 2008-7-6 00:30 發表

 登錄/註冊後可看大圖

If I were Tomy, I would also get bored with 1/10 scale buggies since a close to perfect car has been made...

only missing a lengendary driver like Masami.......

作者: tiger1 時間: 2008-7-6 00:36
frankly, I do not think rc cars are very good for making $$, tmoy has better $$ making lines.

Instead of trying to get Masami or find another Masami, better off close the line and move on to something else, which they did and prosper...

[ 本帖最後由 tiger1 於 2008-7-6 00:54 編輯 ]

作者: minimini 時間: 2008-7-6 00:39
in fact ......I think the M2 pitch drive belt is not good enough.......difficult to set the correct tension...........too loose will slip...........too tight will not smooth ..........

this kind of drive belt had been used in Yokomo 91 works for a short while........but soon was replaced by the currently used belt pitch.......a lot better......

作者: minimini 時間: 2008-7-6 00:40

原帖由 tiger1 於 2008-7-6 00:36 發表

 登錄/註冊後可看大圖

frankly, I do not think rc cars are very good for making $$, tmoy has better $$ making lines. Instead of trying to Masami or another Masami, better off close the line and move on to something else, ...

right......R/C is not Tomy's cup of tea........

作者: tiger1 時間: 2008-7-6 00:44
You are right, that belt pitch was found in Mugen Bulldog, but bulldog is not adjustable, I remember I ran the bulldog for a whole summer in 1985 after my a-level, I was amazed that the drive belts and differentials were nice and clean and close to 100% new when I open the Mugen bulldog chassis after that long summer holiday, which was more than 3 months.

In that summer, I ran that mugen almost every day!!

[ 本帖最後由 tiger1 於 2008-7-6 00:48 編輯 ]

作者: mk9001 時間: 2008-7-6 00:49
喺咪支装巴素???

作者: minimini 時間: 2008-7-8 13:01
the original wheels are 2.2" or 2.0" ??........

作者: tiger1 時間: 2008-7-8 20:36
found it. 2.2 ah

作者: tiger1 時間: 2008-7-8 20:38

原帖由 spoonbb6 於 2008-6-27 17:04 發表

 登錄/註冊後可看大圖

just bought a tomy intruder a few days ago and start the restoration... very difficult..

took me more than 30 mins to clean up one dog bone.....

This car has a slipper?

作者: spoonbb6 時間: 2008-7-8 20:56

原帖由 tiger1 於 2008-7-8 20:38 發表

 登錄/註冊後可看大圖

This car has a slipper?

er... i am new to RC... what is slipper??

作者: minimini 時間: 2008-7-8 23:39

原帖由 tiger1 於 2008-7-8 20:38 發表

 登錄/註冊後可看大圖

This car has a slipper?

I think the original Tomy Intruder comes with a "satellite gear".........while the Tomy EX comes with a fixed spur gear with centre one-way...........

作者: tiger1 時間: 2008-7-9 07:44
you are right, ex has a fixed spur gear and one way.

作者: tiger1 時間: 2008-7-9 07:45
The 'satellite gear' was actually a center differential with straight gears.

作者: minimini 時間: 2008-7-9 12:14

原帖由 tiger1 於 2008-7-9 07:45 發表

 登錄/註冊後可看大圖

The 'satellite gear' was actually a center differential with straight gears.

& what is the function ??........

作者: tiger1 時間: 2008-7-9 16:08
Well, mid differential lor.

Just like 1/8 buggies, have a mid-differential, differential between front and rear axles. Seems that it is not really that useful and as a result we do not see them in 1/10 now

作者: spoonbb6 時間: 2008-7-11 10:11
take out all the sticker, clean up the shell, and with new set of tires!

作者: tiger1 時間: 2008-7-11 11:58
This care is getting very nice.

Spoonbb6: this car has a slipper in the middle?

作者: spoonbb6 時間: 2008-7-11 13:15

原帖由 tiger1 於 2008-7-11 11:58 發表

 登錄/註冊後可看大圖

This care is getting very nice.

Spoonbb6: this car has a slipper in the middle?

no... it's doesn't..

possible to buy one and put in there?

作者: tiger1 時間: 2008-7-11 17:27

原帖由 spoonbb6 於 2008-7-11 13:15 發表

 登錄/註冊後可看大圖

no... it's doesn't..

possible to buy one and put in there?

I also wonder, that is why I asked....

I have one with a mid differential and one with a md-one way. No slipper.....

[ 本帖最後由 tiger1 於 2008-7-11 18:02 編輯 ]

作者: tiger1 時間: 2008-7-11 18:01
Minimini:

Your intruder has a slipper cltuch, was it after market?

作者: minimini 時間: 2008-7-12 01:36

原帖由 tiger1 於 2008-7-11 18:01 發表

 登錄/註冊後可看大圖

Minimini:

Your intruder has a slipper cltuch, was it after market?

my Tomy EX comes with graphite chassis (most likely was made in HK)........& the slipper clutch (was Tomy original option).........

作者: tiger1 時間: 2008-7-12 08:00
Minimini:

Cant you show some pictures of the slipper?

作者: minimini 時間: 2008-7-13 00:36

原帖由 tiger1 於 2008-7-12 08:00 發表

 登錄/註冊後可看大圖

Minimini:

Cant you show some pictures of the slipper?

okok..... I will take some photos soon for your reference.......

作者: jonline 時間: 2014-5-15 17:28
很懷念.... 我二十年前都擁左有部INTRUDER....

作者: honda_vtec 時間: 2014-5-18 15:32
睇返d舊post, 原來好多C兄唔知Intruder 有套Slipper clutch option! 玩Off road 必備，真係正好多！
但用了Slipper clutch就只可用單向，唔可以用衛星齒了

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)