b6ac 叉 AAA 的問題

請問各位師兄,  

找新買咗 部B6AC番來, 但係有啲地方唔係好明, 所以想請教一下

因為岩岩用咗以下o既setting黎叉, 但手摸啲電池好熱, 所以即刻掹晒嘢, 希望有好心人可以教下路

1. 我係用來叉1排四粒(每粒 800mAh) 的 ATMOIC VP800電, 請問, 我SET 0.8A 叉 有無問題?

2. set 0.4A & 0.9V 放電, 有無問題?
3. NiMH CYCLE set - DCHG>CHG  3次, 有無問題?

4. CAPACITY CUT-OFF 我SET幾多先好 (原廠係SET 5000mAh)

5. NiMH Sensitivity D.Peak, 我set 7mV/Cell, 有無問題?

6. 當充電果陣, 右下角咪顯示有幾多mA叉咗入啲電池度o既, 因為電池本身係800mAh, 所以想問下, 究竟叉滿果陣, 去到幾多就夠了 (因為我試過破千, 唔知正唔正常, 所以拿拿聲抆咗啲電)

買这叉机就已經錯，因大陸D叉机唔識cut

1. 我係用來叉1排四粒(每粒 800mAh) 的 ATMOIC VP800電, 請問, 我SET 0.8A 叉 有無問題?
OK

2. set 0.4A & 0.9V 放電, 有無問題? OK
3. NiMH CYCLE set - DCHG>CHG  3次, 有無問.  This function is to use to refresh or activate the battery. No need to use every time.

4. CAPACITY CUT-OFF 我SET幾多先好 (原廠係SET 5000mAh) If for your 800mah MiMH battery, set 800mah, the max capacity cutoff protection.

5. NiMH Sensitivity D.Peak, 我set 7mV/Cell, 有無問題? Default is 4mV/Cell
6. 當充電果陣, 右下角咪顯示有幾多mA叉咗入啲電池度o既, 因為電池本身係800mAh, 所以想問下, 究竟叉滿果陣, 去到幾多就夠了 (因為我試過破千, 唔知正唔正常, 所以拿拿聲抆咗啲電)
It must be lower than 800mAh, cannot over the battery capacity eg. over 1000mah is danger.
If your battery already has some battery,  you only can charge not more than 800maH (max) .......may be 1/3 around 300mAh or 1/2 400mAH

wingscreamer 發表於 2016-1-31 13:26
1. 我係用來叉1排四粒(每粒 800mAh) 的 ATMOIC VP800電, 請問, 我SET 0.8A 叉 有無問題?
OK

Thx ching,

但有個問題，就係我叉AA電果陣，佢識得自動停，但叉AAA果陣，就唔識自動停...好怪

直至尋晚，我試用0.1a去叉電，佢終於識自動停
其實係咩問題呢?

Try to set MiMh Sensitivity D. Peak between 4 to 7mV/Cell to see see any different!
Or in  re-Peak charge mode, set once.

Capacity cut-off should be 800mAh only.

wingscreamer 發表於 2016-2-1 13:57
Try to set MiMh Sensitivity D. Peak between 4 to 7mV/Cell to see see any different!
Or in  re-Peak c ...

如果我四粒AAA電芯裝咗喺一個電池架度(串聯), 咁應該當佢1CELL or 4CELL?