RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
查看: 2394|回復: 18
打印 上一主題 下一主題
收起左側

原裝Slash + 3S A123 測試結果

[複製鏈接]
跳轉到指定樓層
1#
SnackEater 發表於 2009-2-22 18:07:26 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式

遊客登錄

您需要 登錄 才可以下載或查看,沒有帳號?新玩家註冊

x
本來諗住玩全原裝,可惜有車友撞左band,都係換返個2.4接收。其他全原裝無郁過,齒比都係18/86。

原裝電變support 8S NiMH 9.6V,3S A123 9.9V唔多好多,同埋A123其實nominal voltage唔夠3.3V,我一般用3.0V計算,電流大我會用2.8V黎計數添!為左可以更有彈性試唔同config,我嘅3S係2S+1S,用蕉插接駁。

                               
登錄/註冊後可看大圖



                               
登錄/註冊後可看大圖


結果當然係3S1P比2S2P快好多,原裝18/86齒比如果用2S2P A123比NiMH慢,玩到20分鐘直頭覺得太多。3S1P玩到10-12分鐘,直路拍得住brushless!每次都係玩到覺得慢左就唔夠半圈就行唔郁,差電時話得2%,充返22xxmAh!如果係LiPO就漲到升得起都似...

                               
登錄/註冊後可看大圖



                               
登錄/註冊後可看大圖


唔知原裝摩打行3S A123會唔會好快死,死左就換無刷,請問各位師兄Hobbywing 60A夠唔夠玩?有無建議?
2#
ryancmlam 發表於 2009-2-22 20:55:57 | 只看該作者
Eric: have you been to TKO today ? I couldn't see you
3#
 樓主| SnackEater 發表於 2009-2-22 21:26:32 | 只看該作者
原帖由 ryancmlam 於 2009-2-22 20:55 發表
Eric: have you been to TKO today ? I couldn't see you

有呀,不過我驚你唔認得我,無打招呼...
4#
ryancmlam 發表於 2009-2-22 21:40:51 | 只看該作者
原帖由 SnackEater 於 2009-2-22 21:26 發表

有呀,不過我驚你唔認得我,無打招呼...

5#
 樓主| SnackEater 發表於 2009-2-22 22:49:32 | 只看該作者
我今日架戰車

                               
登錄/註冊後可看大圖


我個friend嗰架

                               
登錄/註冊後可看大圖
6#
Moonsideryan 發表於 2009-2-23 02:00:02 | 只看該作者
今日見面你都真係幾快~~
7#
 樓主| SnackEater 發表於 2009-2-23 11:24:11 | 只看該作者
原帖由 Moonsideryan 於 2009-2-23 02:00 發表
今日見面你都真係幾快~~

你係咪問我用咩摩打嗰位師兄?你用緊咩摩打?有無建議俾小弟?
8#
hardmankam 發表於 2009-2-23 11:39:54 | 只看該作者
Hobbywing 60A is ok, maybe look into EC Power set since it is sensored brushless.

For Lipo 2S (7.4): ~ 5000kv motor
For Lipo 3S (11.1): ~ 3500kv motor
For Lipo 4S (14.4): ~ 2300kv motor
It is plenty fast for 2WD!

For A123, maybe choose something 20% faster than the above kv#. (ie 6000, 4200, 2800)
(Since 3v / 3.7v = ~ 80%)
9#
 樓主| SnackEater 發表於 2009-2-23 12:01:44 | 只看該作者
原帖由 hardmankam 於 2009-2-23 11:39 發表
Hobbywing 60A is ok, maybe look into EC Power set since it is sensored brushless.

For Lipo 2S (7.4): ~ 5000kv motor
For Lipo 3S (11.1): ~ 3500kv motor
For Lipo 4S (14.4): ~ 2300kv motor
It is pl ...

Thanks very much for your recommendation. I won't consider EC Power as I saw some players here reported that it failed in their first trial. And I think sensor-less for Off-road should be fine.

I think I will take around 4000kv or lower motor which I can gear it for 3S or 4S A123.
10#
tatame 發表於 2009-2-23 12:17:48 | 只看該作者
原帖由 hardmankam 於 2009-2-23 11:39 發表
Hobbywing 60A is ok, maybe look into EC Power set since it is sensored brushless.

For Lipo 2S (7.4): ~ 5000kv motor
For Lipo 3S (11.1): ~ 3500kv motor
For Lipo 4S (14.4): ~ 2300kv motor
It is pl ...

EC power.... 好多人中招wor

http://bbs.rc-evo.com/viewthread ... &extra=page%3D1
11#
Marco明 發表於 2009-2-24 11:23:02 | 只看該作者
原帖由 hardmankam 於 2009-2-23 11:39 發表
Hobbywing 60A is ok, maybe look into EC Power set since it is sensored brushless.

For Lipo 2S (7.4): ~ 5000kv motor
For Lipo 3S (11.1): ~ 3500kv motor
For Lipo 4S (14.4): ~ 2300kv motor
It is pl ...

其實呢d short course truck用好盈無感4300 kv夠唔夠快(係tko計)???
12#
hardmankam 發表於 2009-2-24 11:56:22 | 只看該作者
原帖由 Marco明 於 2009-2-24 11:23 發表

其實呢d short course truck用好盈無感4300 kv夠唔夠快(係tko計)???


Traxxas Slash is about 2100g... it is heavier than normal 1/10 truggy (~1600g).  So it is better to use 3S + lower kv motor.

If you pair it with hobbywing 9t, it may overheat the motor. Since hobbywing 9t is a 380 class motor!
13#
Marco明 發表於 2009-2-24 12:06:25 | 只看該作者
原帖由 hardmankam 於 2009-2-24 11:56 發表


Traxxas Slash is about 2100g... it is heavier than normal 1/10 truggy (~1600g).  So it is better to use 3S + lower kv motor.

If you pair it with hobbywing 9t, it may overheat the motor. Since  ...

好盈9t唔係540 class咩???我部df-03都用緊呢隻9t
14#
hardmankam 發表於 2009-2-24 12:25:20 | 只看該作者
From hobbywing website on 9T-13T motor:

'This 3650-M sized motor has a core of 380 class motor but the outside appearance is as same as  540 class motor, so its size is suitable for all 1/10 chassis.'
15#
Marco明 發表於 2009-2-24 12:27:21 | 只看該作者
原帖由 hardmankam 於 2009-2-24 12:25 發表
From hobbywing website on 9T-13T motor:

'This 3650-M sized motor has a core of 380 class motor but the outside appearance is as same as  540 class motor, so its size is suitable for all 1/10 chassi ...

原來係咁~~~
咁邊種先係原始540摩打???

[ 本帖最後由 Marco明 於 2009-2-24 12:28 編輯 ]
16#
hardmankam 發表於 2009-2-24 12:34:18 | 只看該作者
原帖由 Marco明 於 2009-2-24 12:27 發表

原來係咁~~~
咁邊種先係原始540摩打???


I think their XeRun Line (8.5T, 5.5T etc...) are 540 class.
All other brands are 540 class. (Orion, LRP, Novak, SP etc...)
All these 540 class case is circular.  Unlike 13T's can, which has 'built-in' heat sink.
17#
hardmankam 發表於 2009-2-24 12:42:53 | 只看該作者
原帖由 Marco明 於 2009-2-24 12:06 發表

好盈9t唔係540 class咩???我部df-03都用緊呢隻9t


Dont worry, DF-03 is light.  Hobbywing 9T is ok.  Just watch your gearing.
18#
Marco明 發表於 2009-2-24 12:47:04 | 只看該作者
原帖由 hardmankam 於 2009-2-24 12:42 發表


Dont worry, DF-03 is light.  Hobbywing 9T is ok.  Just watch your gearing.

明白哂~~~thank you
19#
vones 發表於 2009-2-24 14:59:41 | 只看該作者
Traxxas Slash hit a pole at 55mph+

http://www.youtube.com/watch?v=XybqYW62vc4
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2025-1-12 19:42 , Processed in 0.041794 second(s), 18 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表