我的PROJECT 真.PRO-4

Keep going ! very nice !! ;-)

How thick of the plate of 底盤  ?? looks like very thin...

How thick of the plate of 底盤  ?? looks like very thin...
powis 發表於 2009-9-11 14:44

                               
登錄/註冊後可看大圖

I think It's 1.5mm .. It's scrap metal from old computer case hahahahaa

I think It's 1.5mm .. It's scrap metal from old computer case hahahahaa
kaidogg 發表於 2009-9-11 14:48

                               
登錄/註冊後可看大圖

very thin wor....

very thin wor....
powis 發表於 2009-9-11 20:54

                               
登錄/註冊後可看大圖

No worry ga
After Burn the 支架 to it
the 支架 will 拉 it ... so it won't bend

lol 中英夾雜

45# kaidogg
佢地終於   合體喇

45# kaidogg
佢地終於   合體喇
kaidogg 發表於 2009-9-16 01:54

                               
登錄/註冊後可看大圖

Good luck man!

C hing ......good creative

long tme not back to rc-evo.
this post is quite interesting.
however, i do concern on some points of this car as i have made this type of cars before also.
1. i support kaidogg that the 支架WILL 拉, AND it will not bend. however,  i do think that it will cause the whole structure broken once crash.
2. the structure seems like too thin and week. better get a thicker and stronger material to do that.

Anyway, I do support DIY and your spirit and idea is really good. I think you maybe just mis-use of the materials. That is what DIy-ers will try when learning and testing. By be sure that, take every brother in this forum opinion to consider and you will finally get a good car.

long tme not back to rc-evo.
this post is quite interesting.
however, i do concern on some points of this car as i have made this type of cars before also.
1. i support kaidogg that the 支架WILL 拉 ...
deadmatch 發表於 2009-9-16 11:42

                               
登錄/註冊後可看大圖

yes yes very good comment ....
as u said ... Have to Test (when It's finally done and still have long way to go hahaaha)
I can't say that It's structure is strong enough or not

I just use What ever I can get easily and I can hanadle ..

EG . metal board too thick ? I can't cut myself
metal rod too think I can't bend then or Weld them

so ... base on what I can use I make this current design   and adjust it along the way


really thanks for the comment .. really helpful and useful

ps about the 拉 part ... is I THINK it will work only hahaaahahhaa

PS2 i do think that it will cause the whole structure broken once crash.
I really really really hope that this point is wrong ... if really happen .. i want cry

yes yes very good comment ....
as u said ... Have to Test (when It's finally done and still have long way to go hahaaha)
I can't say that It's structure is strong enough or not

I just use Wha ...
kaidogg 發表於 2009-9-16 17:13

                               
登錄/註冊後可看大圖

M.....actually it is really different for making a real car and a rc.
give you two pictures of what i am working now.
i am not saying this is good enough but i do think it must stronger structure than your car for crashing.XD
don't hope for the point, the whole structure links together and even a small parts damage needed to change the whole chassis......

M.....actually it is really different for making a real car and a rc.
give you two pictures of what i am working now.
i am not saying this is good enough but i do think it must stronger structure  ...
deadmatch 發表於 2009-9-16 20:45

                               
登錄/註冊後可看大圖

Why not solid rear axel ?

once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC

once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC
deadmatch 發表於 2009-9-16 20:58

                               
登錄/註冊後可看大圖

but if you install Roll Bar system it will be ok ?

54# kaidogg

by the way
my car is based on this real truck
so ... should be strong enough
I tried to THROW my cage out the windows and is ok wor
I live in 1st floow

you know that the sudden impact is much much bigger .....
i know your car is base on the real car.  but for a real car , when it crash, it will collapse also.....
but for RC don't.......

Ture Ture


so ... I HOPE i won't crash HARD
people don't crash me please hahaahah
by the way
I don't think my car will Run well too ... but I just want to Build it ... everything is AFTER WORDS
hahaahahah

support me support me la

ps I really mean that I throw out the window

once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC
deadmatch 發表於 2009-9-16 20:58
but if you install Roll Bar system it will be ok ?

it will be better.
you idea is good, but better for choosing the material.
i think use 2-3 mm thick aluminium alloy will better
also, 4mm steel bar to make the chassis will be the best.

it will be better.
you idea is good, but better for choosing the material.
i think use 2-3 mm thick aluminium alloy will better
also, 4mm steel bar to make the chassis will be the best.
deadmatch 發表於 2009-9-16 21:19

                               
登錄/註冊後可看大圖

aluminium alloy Can't be Weld wor ...
I have that at home but when I weld it ... it Melts