無416,無T09,無BD5,只有玩盡架TC5 !

This is my TC 5, and I think AE should do something to their design with the motor mounted too far out wards. So I had done my conversions.
Awful lot of work has been done. Motor mounted located inside the bulkhead.

                               
登錄/註冊後可看大圖

Tamiya TB03 alu/out drives were used to the rear pulley.

                               
登錄/註冊後可看大圖

Top deck was raised up 2mm by FRP, center pulleys were machined and location rearranged.   

                               
登錄/註冊後可看大圖

The car now very balance btw left/right with out additional weight, over all the motor mounted 7mm inwards.

                               
登錄/註冊後可看大圖

Thanks for reading, and any positive/negative comments are welcome.

將尾波箱距離做窄左?

師兄DIY精神可嘉, 試左車未? 左右平衡會好一點嗎?

因為TC 5 個motor 太出, 6mm以下 ride hight 點走都店地,...所以要改.
一改位....左又要改,右又要改...不過都做到了.
Motor 入番7mm 同d 416, BD4呀 差吾多..冇左motor 店地, 右彎好好多, 電池個邊加左 Transponter時跑 就好 balance !

AE TC5 / TAMIYA 416  side by side comparison:

                               
登錄/註冊後可看大圖

MY TC 5 after mod:

                               
登錄/註冊後可看大圖

good job!

因為TC 5 個motor 太出, 6mm以下 ride hight 點走都店地,...所以要改.
一改位....左又要改,右又要改...不過都做到了.
Motor 入番7mm 同d 416, BD4呀 差吾多..冇左motor 店地, 右彎好好多, 電池個邊加左 Transpont ...
Angtr 發表於 14/10/2009 20:14

                               
登錄/註冊後可看大圖

其實MOTOR HI到地係好正常, 小弟玩008, 416 都係襟.... 唔需要刻意SET高車高....
不過TC 5 放MOTOR 就真係放得幾出下(我有FD有...)..

而家出左d倣短小小既motor, 雖然動力較差, 但如果唔識好似你咁diy既, 都可以用得過既

E...C兄都係鍾意玩海綿呔

有頭髮, 邊個做"辣尼"....因為匯水問題...d 416 ..T09 太貴...只好選TC5...
同因為我地冇得用"o太水"只有用海綿呔....

平有平玩, 貴有貴玩o者
我又覺得玩海綿呔幾好玩o丫, 只係磨損比較快o者

good job!

師兄好嘢
我想問你用邊隻牌子尾珠差同中軸去改?

師兄好嘢
我想問你用邊隻牌子尾珠差同中軸去改?
joey.c 發表於 2009-10-14 23:44

                               
登錄/註冊後可看大圖

用星星 TB03 尾珠差 set+珠差碟.
個bearing軸要磨短0.8-1mm,因為ae 用2.34mm珠, 再用5mm shim, shim 到可以用1個850 bearing 夾住pulley 同長個邊out drive, 砌好兩邊,個pulley 吾走位就ok .
沙紙磨大小小個 out drive"我就用機器做"! 因 tamiya dog bone end係6mm, ae  dog bone end係6.3MM , 用番Tamiya blades, ok! 中軸冇改只張d pulley 轉位!