想翻新部車... (十年以上)

清潔前....

                               
登錄/註冊後可看大圖

清潔後...

                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖

另外哩4條避震都應該打左柴，各位師兄有咩平野介紹．．．

回復 19# keidub0322

u may use ta03f for drifting lor.......

also u have to change 萬向， bearing and some plastic parts..if dont ,your car is easy to break..

回復  keidub0322

u may use ta03f for drifting lor.......

also u have to change 萬向， bearing ...
freeboy303 發表於 2010-8-12 00:02

                               
登錄/註冊後可看大圖

師兄．．．　咁想請問下係咪唔洗換電變／摩打呢？　　
drifting 呔又要幾錢呢?

回復 24# keidub0322


    u may use mc230 or 330 with 21 t motor is enough for drifting

a set of drift tire with link under 80$

下???  D牙已經停產．．．．　 咁點算呀... 重諗住換個快d既摩打tim....
keidub0322 發表於 2010-8-11 23:53

                               
登錄/註冊後可看大圖

我就係頭痛緊D齒,o岩o出整緊部反胎漂移車,點知隻大齒原來ko左幾牙,都唔知去邊度搵...唉

已經清潔完畢，明天去kws 入以下貨品!

1) 新殼
2) mc 330 + 21t motor
3) drif 呔
4) 新電池 (想問下買邊隻好d)
5) 避震
以上大概要幾錢?

重有咩要補給，請師各兄提點!

回復 27# keidub0322


    1) 新殼$180
2) mc 330 + 21t motor.. suggest u to buy 2nd hand
3) drif 呔$80
4) 新電池 (想問下買邊隻好d)..SE,BY,IP i have used these brand ,is ok...
5) 避震 TRF ..$$300

回復  keidub0322


    1) 新殼$180
2) mc 330 + 21t motor.. suggest u to buy 2nd hand
3) drif 呔 ...
freeboy303 發表於 2010-8-12 08:39

                               
登錄/註冊後可看大圖

Thanks ！ freeboy 兄！另外想問下邊度有Ta03F 底板買呢？

ching, honestly speeking it's not worth to spend HK$300 避震 for the car la, even you spend more $$$ the final performance will not be compare to new car, may be you can consider FF03PRO if you like front mount motor ....

ching, honestly speeking it's not worth to spend HK$300 避震 for the car la, even you spend more $$$ ...
gimsink 發表於 2010-8-12 10:31

                               
登錄/註冊後可看大圖

我原全明白不能同新車相比，但係我只想佢再開動返！重拾玩車既樂趣！就好以toy story  一樣！

Resumming an old car to a runnable condition is a kind of pleasure that you will not find in builduing new car. I spend many time to rebuild Avanti and RC10T ( especially 10T, still my masterpiece even it's 20yrs old ). However not able to rebuild Lazer and Cat due to no replacement part....
ching go ahead la, remember to post your car after finish !!

Resumming an old car to a runnable condition is a kind of pleasure that you will not find in buildui ...
gimsink 發表於 2010-8-12 12:54

                               
登錄/註冊後可看大圖

Thanks ching support!! I will work hard ar... I will post the new photo once the car is re-new.   Tks again!

要買新啤令呀！！

以上網徵求2手件.... 希望有回覆啦....

mc330 電變/ 21t 摩打 @@? 唔買2手好盈35A+9T 都係$250-$300左右
見你4條避震好似冇咩事.我諗換左避震油+O"榮"就ok了

mc330 電變/ 21t 摩打 @@? 唔買2手好盈35A+9T 都係$250-$300左右
見你4條避震好似冇咩事.我諗換左避震油就 ...
EX超龍 發表於 2010-8-12 13:45

                               
登錄/註冊後可看大圖

Freeboy 師兄提意摩打唔好太快会好易畫牙，而d牙已停產... 買唔返!  所以建議買以上摩打!!

條避震底部都已經磨到"zit" 晒，所以想買過條新既!

Freeboy 師兄提意摩打唔好太快会好易畫牙，而d牙已停產... 買唔返!  所以建議買以上摩打!!

...
keidub0322 發表於 2010-8-12 13:52

                               
登錄/註冊後可看大圖

    @@" d牙 觀塘仲有得買 我見好似仲有十幾包 $2x-$3x包 (有黑色/白色)...仲有好似部份牙係同M03共用的

                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖

@@" d牙 觀塘仲有得買 我見好似仲有十幾包 $3x包 (有黑色/白色)...仲有好似部份牙係同M03共用的
EX超龍 發表於 2010-8-12 13:54

                               
登錄/註冊後可看大圖

  可否PM 地扯！Tks！

可否PM 地扯！Tks！
keidub0322 發表於 2010-8-12 14:19

                               
登錄/註冊後可看大圖

偉利模型...全個地址唔識點打=="sor