Pan Car Galaries ^^

Hello all Pan Car Ching

Would you mind sharing your finished pan car (1/10 or 1/12, 扮Pro Ten 都得架), on and off shell here? ^^

Hope more Ching will join the Pen Car party !!!

Thank you very much !!!

Here is my Xray XII link car

好靚，但個幾條摩打線頂住左條油壓，會阻住扭腰

好靚，但個幾條摩打線頂住左條油壓，會阻住扭腰
hlsk 發表於 2011-2-1 13:35

                               
登錄/註冊後可看大圖

Hi Ching, my cable layout is not looking good but I have no issue on the damper since there is room under the body shell for the cables ^^

回復 5# mikuro

Thz Ur call, btw, where and when u will ground it? Interest to c how it performs.

小小意見，個ESC線換16G，幼D，軟好多，減少對扭腰影響，原裝的太粗，太硬了，12仔可以幼D。用放在中間是ok的，因為成個12仔殼最高位就是中間，唔會頂住個殼(唔平)，另外，所有電線的長度要小心處理，長短得宜，才不會影響扭腰，有錯請指教，謝謝!

回復  mikuro

Thz Ur call, btw, where and when u will ground it? Interest to c how it performs.
hlsk 發表於 2011-2-1 14:43

                               
登錄/註冊後可看大圖

    Normally, me and some Ching will play at JV on weekend. If you have 2WD car as well, you can join the party as well. ^^

小小意見，個ESC線換16G，幼D減少對扭腰影響，原裝的太粗，太硬了，12仔可以幼D。用放在中間是ok的，因為成 ...
derek5 發表於 2011-2-1 14:57

                               
登錄/註冊後可看大圖

    Hi Derek, it is good to see more pan car coming. Your CRC is looking great ^^
    Can you show us your shell as well?
    Yes, even the built-in cable is still okay but I agree to change to thinner cables. Thanks for sharing ^^
    Btw, are you using 4.5T motor? Have you play at JV before? ^^

回復 9# mikuro

no, i'm living in YL, will go to TC or TRC in sometime.....

Hi Derek, it is good to see more pan car coming. Your CRC is looking great ^^
    Can you ...
mikuro 發表於 2011-2-1 15:04

                               
登錄/註冊後可看大圖

i'm using 4.5T and want to try 4.0T later, how about you?

回復  mikuro

no, i'm living in YL, will go to TC or TRC in sometime.....
derek5 發表於 2011-2-1 15:14

                               
登錄/註冊後可看大圖

Alright then ^^
Nice shell. Thanks for sharing ^^

i'm using 4.5T and want to try 4.0T later, how about you?
derek5 發表於 2011-2-1 15:18

                               
登錄/註冊後可看大圖

    I am using X12 4.0T ^^

回復 8# mikuro


    Thx for the invitation and love to grasp some knowledge from Ching like u

回復  mikuro


    Thx for the invitation and love to grasp some knowledge from Ching like u
hlsk 發表於 2011-2-1 16:25

                               
登錄/註冊後可看大圖

Tell you what, I am a beginner and I just picking up 1/12 pan car again since JV was born. ^^
Also, there are Ching here that sharing a lot more information on pan car as well.

回復 1# mikuro


    First time show my F104 pan car here!! haha and some shell of 1/10 pan car

登錄/註冊後可看大圖

回復  mikuro


    First time show my F104 pan car here!! haha and some shell of 1/10 pan car
raymomo 發表於 2011-2-2 00:06

                               
登錄/註冊後可看大圖

    Thanks Ray for sharing. ^^
    Seems you wanna to get Corally Pro Ten as well. GoGoGo ^^

回復  mikuro


    First time show my F104 pan car here!! haha and some shell of 1/10 pan car
raymomo 發表於 2011-2-2 00:06

                               
登錄/註冊後可看大圖

very nice....f37 r35 ?
f104 have a abc leman shell....if use normal oil car tire...it good fit (180mm width) as I saw one ching try before.....it is good because large range oil car tire degree can choice and more cheap.....speedmind oil tire only $90 1 set.......

show some of mind...but now all are dirty and some is retire...
they are f109..f103..f103GT....ae 12r5 ......

回復 17# mikuro


    already have waiting list in red star!! but one big trouble thing is the parts problem,need to ask them more details about it!! pick up u CRC already?

回復 18# abcde


    yes ar F37 F35! any other choice of the more solf rear tire??