--Will apply the IFMAR Rules with some modifications to the schedule of events.
--3 results out of 4 in the world model 1/10 the 200mm Touring car Race (Open) will be reckoned in to the qualification of 2012 World Championship Trial
Lap Counting:
AMBrc lap counting system will be used
AMBrc Direct Powered transponder must be used
Numbers of drivers are limited to:
1:10 class: 60 drivers
1:8 class: 50 drivers
Qualify:
10 minutes qualify for each heat in each class
3 rounds of Qualifying Heats. Using best result of each driver to place their seat in main final.
Main Final:
15 minutes for C, D ,E & F Main Final
25 minutes for B Main Final
30 minutes for A Main Final
Body
1/8 & 1/10
All drivers must use IFMAR registered Body shell
Foam tires only
1/10 200mm:
All drivers must use 200mm body shell
Only the following holes and sizes are permitted in the body shells:
One 15mm maximum diameter hole in the roof for glow plug access
One 60mm maximum diameter hole in the roof for fuel refill
Both front side windows and the rear window can be removed for ventilation, except for the side rear windows, which must remain intact
One small hole with maximum 10mm diameter can be made for the transponder
One small hole with maximum 10mm diameter can be made for the radio antenna
One small hole with maximum 20mm diameter can be made for the exhaust pipe
No other holes are permitted
Tire
1/8th and 1/10th: Foam tires only
Fuel:
must use (25%)Fuel for the Race.
Checking
Racing cars will be check for analysis and any competitor found to be offending the rules will be disqualified and any race result obtained will be null and void
Car Specification
1/10th Technical Specifications:
The official measurements in these Technical Specifications are the metric measurements.
1) 200 mm Nitro Touring Car which will be 4WD
2) The engine may have a total capacity of not more than 2.11cc only. The engines may have a maximum of four (4) ports in the liner, including the exhaust port
3) Maximum 2-speed gearbox allowed
4) The Fuel tank capacity to be 75 cc including all fuel tubings, filters, etc.
5) The mufflers and INS boxes have to bear their homologation numbers during the entire competition. The mufflers’ and INS boxes’ measurements (both internally and externally) have to conform with those on the homologation sheet issued by IFMAR.
6) Front Tires maximum width: 26 mm
7) Rear Tires maximum width: 30 mm
8) Only bodies that are recognized and approved by IFMAR will be allowed.
9) Overall dimensions:
Maximum width 205mm (with body)
Maximum height 175mm (with wing, body and Gurney strip with 10mm spacer block)
Minimum weight 1725 grams (with empty fuel tank and with timing transponder installed.)
1/8th Technical Specifications:
The official measurements in these Technical Specifications are the metric measurements.
1) All brands of 1/8 ON-ROAD 4wd car kit will be allowed.
2) The engine may have a total capacity of not more than 3.5 cc. No tolerance allowed.
3) Maximum 2-speed gearbox allowed
4) The Fuel tank capacity to be 125 cc including all fuel tubings, filters, etc.
5) The mufflers and INS boxes have to bear their homologation numbers during the entire competition. The mufflers’ and INS boxes’ measurements (both internally and externally) have to conform with those on the homologation sheet issued by IFMAR.
6) Front Tires maximum width: 37 mm
7) Rear Tires Minimum width: 64 mm
8) Only bodies that are recognized and approved by IFMAR will be allowed.
9) Overall dimensions:
Maximum width 277mm (with body)
Maximum height 180 mm (with wing, body and Gurney strip with 10mm spacer block)
Minimum weight 2525grams (with empty fuel tank and timing transponder installed.)
