KEYENCE 電變 setup 問題

下圖果個電變有無朋友知道要點 set???....我用 set futaba 果 d 方法都 set 唔到...個電變只係一路必必響...說明書又淨得日文...

I have A-07RZ,but my instruction manual is english.
i think can use for A-07VZ.

1.Turn the ESC on and hold downthe set switch for approximately 5seconds.
2.the red LED will begin flashing.
3.release the set switch.
4.Set the trasmitter throttle to"Neutral" and press the SET switch once.
5.The red LED will flash faster.
6.Set the transmitter throttle to "High point"(at 90%of full throttle) and press the SET switch once.
7.The red LED will flash slower.
8.Set the transmitter throttle to "Brake point"(at 90%of full brake) and press the SET switch once.
The setup is completed.

原帖由 12cm 於 2006-9-20 22:35 發表
下圖果個電變有無朋友知道要點 set???....我用 set futaba 果 d 方法都 set 唔到...個電變只係一路必必響...說明書又淨得日文...

I am using this ESC also, mine has English manual!!  The most important is to set the throtte not 100%, it is 90%...
Interesting!!

點 set 90% of full throttle...90%of full brake呀???拉雞唔拉盡???好難掌握 wor

Yep, that is the point, try!!

想問埋...呢隻係唔係一隻可靠既 esc???用 tz 大齒 102 摩打齒用 36 或 37 齒比 6.375 或 6.2 響 ta05 度有無問題呢??

I have beening using it for months for my frog with 23T.  I don't have any problem.  I classify this ESC as middle and up.

原帖由 12cm 於 2006-9-21 00:16 發表
想問埋...呢隻係唔係一隻可靠既 esc???用 tz 大齒 102 摩打齒用 36 或 37 齒比 6.375 或 6.2 響 ta05 度有無問題呢??

我用A-07RZ+TZ+TB-02R,我覺得佢幾好用.
雖然線性係差D,但係夠爆.

原帖由 12cm 於 20/9/2006 11:41 PM 發表
點 set 90% of full throttle...90%of full brake呀???拉雞唔拉盡???好難掌握 wor

其實呢...........hi point應該係個控度較,brake都係~

原帖由 ALEXANDER 於 2006-9-21 08:19 發表

其實呢...........hi point應該係個控度較,brake都係~

ｇｏｏｄ　ｍｏｒｎｉｎｇ～～咁早呀～

原帖由 SPOONACCORD 於 21/9/2006 08:21 AM 發表

ｇｏｏｄ　ｍｏｒｎｉｎｇ～～咁早呀～

早晨~通頂整車Y麻!!!

我想問呢個電變點樣 off 後波.....同埋有一條黃色幼電線有咩用架....跟包裝果三粒好似電容咁既野...又有咩用架...

原帖由 12cm 於 2006-10-3 23:13 發表
我想問呢個電變點樣 off 後波.....同埋有一條黃色幼電線有咩用爰邞G三粒好似電容咁既野...又有咩用架...

1 ) 聽 o的師兄講, 呢隻 ESC 無得 Off 後波
2 ) 黃色幼線係舊的 FET Servo 用的 7.2V 供電
3 ) o個 3 粒正正就係電容, 1 粒銲住摩打 + 同 - , 一粒銲 + 同摩打殼, 最後一粒銲摩打 - 同摩打殼

turn the BT to "infinity" = the ECS will wait forever for reverse.  That mean reverse is off, according to menu.

原帖由 benz1850 於 2006-10-4 01:16 發表
turn the BT to "infinity" = the ECS will wait forever for reverse.  That mean reverse is off, according to menu.

Set the reserve delay time is a good idea !!