求救Xray 頭呔 一轉彎， 條長皮帶就會好噪，同埋嫁好震

sunnyho710 發表於 2012-3-20 12:23

                               
登錄/註冊後可看大圖

請問 Ching 有冇好似我咁 ， 咁噪 ，同震？

no ar... i feel good wor
my setting is Turn 25 degree each side when i measure on the set-up tools

patshiu 發表於 2012-3-20 12:58

                               
登錄/註冊後可看大圖

no ar... i feel good wor
my setting is Turn 25 degree each side when i measure on the set-up to ...

but i'm slow driver.. only using 8.5T Motor and 23T Pinion gear

patshiu 發表於 2012-3-20 13:00

                               
登錄/註冊後可看大圖

but i'm slow driver.. only using 8.5T Motor and 23T Pinion gear

I also slow drive in 10.5T,
I had set 20 degree only but also have this noise and not smooth,
Is any problem in my assemble ?

sunnyho710 發表於 2012-3-20 13:35

                               
登錄/註冊後可看大圖

I also slow drive in 10.5T,
I had set 20 degree only but also have this noise and not smooth,
Is ...

maybe you try other Ching's suggestion
1. change the wheel to test first
2. add belt top to limit the belt
3. double check the direction of the ring (which for adjust the tension of belt) both side to ensure both sides are set to same location
4. check the direction of the "Big" gear, "with screws head facing to the rear belt"

I'm newbie only.. so just to discuss, if i'm wrong dont kick me too hard..

patshiu 發表於 2012-3-20 13:54

                               
登錄/註冊後可看大圖

maybe you try other Ching's suggestion
1. change the wheel to test first
2. add belt top to limi ...

Thanks for your advise

privateroad 發表於 2012-3-20 10:21

                               
登錄/註冊後可看大圖

建議你買過架~安迪好似重有貨

送你個嫁比我VBC底板

唔盡軚震唔震先
唔震就冇咩問題,都震先有事
2節係唔可以set盡哂個軚角

唔盡軚都係震，應該係萬向問題
而家換佐三節棍，所有問題都解決哂
Thank you 咁多位Ching 

好明顯係萬向問題啦，咁多CHING俾一樣既意見你。想解決就換三節棍，唔換就調細D轉向角度

你咁既情況100%正常.原裝車係會咁，要option 去三節棍，用了三節棍後，還要小心保養上實櫺仔所有機米仔。

b9605084 發表於 2012-3-21 23:44

                               
登錄/註冊後可看大圖

你咁既情況100%正常.原裝車係會咁，要option 去三節棍，用了三節棍後，還要小心保養上實櫺仔所有機米仔。

Thanks for Ching remind.
是三節棍上的機米仔嗎？

收到，3q Ching 

除非要飄移，一般玩快車根本唔駛紐咁盡呔盤。

除非要飄移，一般玩快車根本唔駛紐咁盡呔盤。