SCP10MW01 Alum Multi width HEX HUB 30 to 60mm This is the Hot Racing Multi width Hex Adapters for the Scorpion ax10
Series. Fit other 5mm axel like Wheelie King
FEATURES:
CNC 6061-T6 Aluminum construction
Widen 15, 20, 25 or 30 mm (per side)
Black in color
YOU WILL RECEIVE:
Four Light weight 15mm Hex Adapters
Four 15mm hex adapter
Four 5mm Hex adapter
Four HD Hot Racing Wheel Washer
Four 15mm Cap Screw
Four 25mm Cap Screw
Four o-ring
Four lock pin
Four 5x8 shim
REQUIREMENTS:
SDM25 2.5mm Wrench
SPECIFICATIONS:
length: 15 and 20 (mm)
Hex Size: 12mm
Inside diameter:4.58 mm
BVS20X01 LPSS Black Velcro Straps 200mm These are Velcro Battery Straps for most Vehicles. FEATURES:
LPSS Very strong low profile spring steel buckle Black Steel Buckle work together with polyester Velcro straps to create a secure holding with low profile configurations Velcro construction Black in color YOU WILL RECEIVE:
Two Battery Straps REQUIREMENTS:
WRA39L Dig unit for Wraith transmission
This is a add on dig unit (rear wheel lock out) for your stock Wraith transmission
FEATURES:
3 modes:
a) rear wheels drive (4X4)
b) rear wheels locked (will not spin)
c) rear wheels free spin (4X2)
CNC #45 Carbon Steel coupling with nitride coating to increase wear resistance, and enhance corrosion resistance
Bronze linear bearings and Rubber cushioning linkage give smooth synthesized shiftaction
YOU WILL RECEIVE:
Steel Hex coupling with nitride coating
one dig unit with mounting hardware
REQUIREMENTS:
Axial Warith complete gearbox with gear and screw.
One standard servo and servo arm
Three or more channel radio sysem
ACC468K01 1/10 scale white bungee cord kit This is a set of 1/10 Scale bungie cords. Great for holding down your scale parts! FEATURES:
A model replica of a 1/10 Scale bungie cords Detailed accessories Can be customize the length you need. YOU WILL RECEIVE:
One 1.2M (4ft) long 1/10 Scale bungie cords 14 lock ring (two had been installed) 12 Hook (two had been installed) SPECIFICATIONS:
Scale: 1/10 COMMENTS:
use crimping tool or Pliers to Crimp down the lock Ring Not intended as a toy holding down your scale parts!
TD100X06 Alum. HD Big Bore Shock (2) 100mm This a Hot Racing Big Bore Set of for the Traxxas and most Off Road truck truck use 100mm shock.
FEATURES:
CNC Aluminum Big Bore Cylinder Construction
Anodized Silver in Color
Fully Assembled
Heavy Duty Duar Rate Springs
Heavy Duty 3.5mm Shock Shaft
YOU WILL RECEIVE:
Two Assembled Aluminum shock
Two M3x20mm flat head screw
Two M3x18mm cap head screw
Two 3mm Countersunk Washer
Two 5.9 hollow ball
Four 1.5mm thick spacers.
Four 3mm thick spacers
REQUIREMENTS:
Filling shocks with shock oil and assembling onto the model.
If Use it on other truck might need different hardware
SPECIFICATIONS:
Replace Traxxas Big Bore EX Long Shock TRA2661, 3762, 3762A, 2662
length: 105mm (4-1/8") (not compressed)
Mounting point 100mm (4")
diameter: 19mm (3/4")
Steel Shock Shaft 3.5mm
Sping 1.54mm wire
Dual rate 13 Turn Comment
Accept optional Shock boot if need.
Can be use with this Hot Racing Spring SLF63FS261 SLF63MR268 SLF63RS286
Must Bleeding the shock,
1) If the shock shaft push out more the 6mm(1/4").
2) If you can not push the shock shaft all the way in. THERE IS TOO MUCH OIL. Loosen the cap a half turn put the shock shaft in to pump out the excessive amount of oil
Tips
Make sure oil are fill to the top with no air in the oil and when Screw down the cap the shock shaft should be about 3 to 4mm out.
樓主: hobbyhobby
樓主
