RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
樓主: macau-rc
收起左側

Tamiya RM-01 full option

  [複製鏈接]
Zenki 發表於 2012-7-5 11:17:10 | 顯示全部樓層
What gear ratio and battery (what mAh) you used? Can play for how long? Thanks sharing!
 樓主| macau-rc 發表於 2012-7-5 11:33:09 | 顯示全部樓層
回復 Zenki 的帖子

IP 6200 3.7V, Dualsky 8.5D stock motor (around 4000KV), 96/35, over 8 minute
albertau2011 發表於 2012-7-5 11:44:46 | 顯示全部樓層
96/35 ? any over heat
 樓主| macau-rc 發表於 2012-7-5 14:19:47 | 顯示全部樓層
回復 albertau2011 的帖子

for 1 cell no problem, coz is 8.5T motor
svsv 發表於 2012-7-5 14:30:13 | 顯示全部樓層
corkscrew 發表於 2012-7-5 15:21:25 | 顯示全部樓層
macau-rc 發表於 2012-7-5 09:44
昨晚第一次玩,感覺良好,只是roll damper油希左d,見意頭4mm螺絲換長d。

GT300喎~
albertau2011 發表於 2012-7-5 18:53:49 | 顯示全部樓層
macau-rc 發表於 2012-7-5 09:44
昨晚第一次玩,感覺良好,只是roll damper油希左d,見意頭4mm螺絲換長d。

C Hing, roll damper   用 ? 油 , 20000?
 樓主| macau-rc 發表於 2012-7-6 09:16:37 | 顯示全部樓層
Trinity 30WT, now change to 45WT
Zenki 發表於 2012-7-12 16:51:35 | 顯示全部樓層
macau-rc 發表於 2012-7-5 11:33
回復 Zenki 的帖子

IP 6200 3.7V, Dualsky 8.5D stock motor (around 4000KV), 96/35, over 8 minute

Which barnd are you using for the Supr Gear, Diff Ball and Diff Ball Plate?
 樓主| macau-rc 發表於 2012-7-12 18:08:11 | 顯示全部樓層
Diff ball and diff ball plate are original, Supr Gear is Kawada
ThomasZ 發表於 2012-7-13 02:09:57 | 顯示全部樓層
請問RM-01放唔放到2CELL的LIPO?
 樓主| macau-rc 發表於 2012-7-13 09:16:17 | 顯示全部樓層
放到2CELL short pack
Zenki 發表於 2012-7-13 10:36:30 | 顯示全部樓層
macau-rc 發表於 2012-7-12 18:08
Diff ball and diff ball plate are original, Supr Gear is Kawada

ar ha, thx for ur reply!
Lotus 發表於 2012-7-13 11:01:35 | 顯示全部樓層
用到其它廠呔呤?
 樓主| macau-rc 發表於 2012-7-13 11:50:42 | 顯示全部樓層
用到, rear is std, front change 8x5F bearing can use 其它廠呔呤
 樓主| macau-rc 發表於 2012-7-13 11:54:05 | 顯示全部樓層
Or........

54366 RM-01 Front Upright Shaft (for 1/8x5/16 Inch Bearing)
The upgraded upright shafts are a replacement of the standard shafts used in the stock plastic uprights. These allow the use of aftermarket 1/12th scale wheels that use the 1/8 x 5/16th inch bearings. The standard wheel axle uses metric size bearings for use on Tamiya wheels. The use of inch size bearings will open up the racers options.
gallery_54366a.jpg
Zenki 發表於 2012-7-13 19:39:26 | 顯示全部樓層
本帖最後由 Zenki 於 2012-8-6 16:00 編輯
macau-rc 發表於 2012-7-12 18:08
Diff ball and diff ball plate are original, Supr Gear is Kawada

Kawada spur gear for RM-01 (#TRM03; 88T0-100T), right?
vlwwh 發表於 2012-7-16 21:13:51 | 顯示全部樓層
扭腰油壓可改裝用於肉都無?
gx2081 發表於 2013-2-1 02:51:33 | 顯示全部樓層
我買了yokomo 12仔後呔但裝到RM01身上點解?
jypepe 發表於 2013-2-1 03:05:29 | 顯示全部樓層
gx2081 發表於 2013-2-1 02:51
我買了yokomo 12仔後呔但裝到RM01身上點解?

http://rc-evo.com/xbbs/forum.php ... hlight=yokomo%2Br12

因為係YOKOMO 專用
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2024-3-29 14:32 , Processed in 0.039957 second(s), 16 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表