叉 IB4200 電既問題

叉 IB4200 電既問題

通常set d-peak幾多去叉?

我set 部叉機(lrp pulsar competition)用5a叉電, d-peak set 10mV
叉到35XXmah 就停左, 4000仟都過唔到, 何解?

順帶一提, 我已在焊好電後先用discharge mode放清左d電先叉架喇.

I set delta peak 3mV, it always stops at around 4100 - 4300.

用5a差英該無問題。。。

原帖由 ellis 於 2006-11-13 18:04 發表
叉 IB4200 電既問題

通常set d-peak幾多去叉?

我set 部叉機(lrp pulsar competition)用5a叉電, d-peak set 10mV
叉到35XXmah 就停左, 4000仟都過唔到, 何解?

順帶一提, 我已在焊好電後先用discharge mo ...

The manual said use 6A to charge. d-peak at 3 - 4 mV. Do not use fan to cool it down.

Also never overheat when charging the battery (never above 50 C)

If fail cycle a few times (discharge then wait then charge then wait then discharge etc.

If still don't work try to find a friend with Spintec battery manager to discharge the battery. It may improve the performance.

而家d4xxx電差極都唔多過4-500.....d 3300反而可差到3800.....3800又差到4千1-2

你有無同感!

我........我4200可以差到48XX喎~

我都係用Pulsar, 差GP3300通常around 3100-3200mah, 唔同差機應該會有出入, 唔可以從數字上一概而論...

真係明白........
點解 D 人咁著重 D 電差到幾多呢????.........

原帖由 yokomo-SD 於 2006-11-14 11:08 發表
真係明白........
點解 D 人咁著重 D 電差到幾多呢????.........

無論千三定三千,用得既就係正電啦

原帖由 yokomo-SD 於 2006-11-14 11:08 發表
真係明白........
點解 D 人咁著重 D 電差到幾多呢????.........

想爆同玩得耐D掛....

買排4200差唔足唔底嗎!

原帖由 yokomo-SD 於 2006-11-14 11:08 發表
真係明白........
點解 D 人咁著重 D 電差到幾多呢????.........

因為玩耐d .......

原帖由 ALEXANDER 於 2006-11-14 00:54 發表
我........我4200可以差到48XX喎~

勁呀!

i use 4a charge

原帖由 simonwang002 於 2006-11-14 17:08 發表
i use 4a charge

4a差幾多?好d嗎?

我用orion adv. 5A 3mv 都去到48xx

I use Orion advantage 6A charge 3 mv d peak, and a few IB 4200 batteries can charge to at least 4600 mah.

However, I also have a pack IB of 4200 mah who had low voltage and dead after just 1 to 2 charge. And another pack who deteriorate rapidly after a few charge. I think there is a QC problem in some batch of IB 4200 battery.