TT-02 玩家討論區

今日改少少先

I have been using a HW 60A 13.5T. The plastic center shaft seemed OK so far but I already broke a front knuckle, a rear C hub, a steering joint and deformed a crome plated rim so far. No direct full speed crashes, just occasional bumps. So I think the TT02 plastic parts are quite fragile. Now I tried to reduce their brittleness by puuting them into boling water and let it cool before using.

YSL 發表於 2013-7-23 23:51
今日改少少先

C hing, change the plastic center shaft la

tsfai 發表於 2013-7-23 19:18
A Ching runs 4t with full turbo in jv. One gear broke after 4 pack lipo

4t !!!!  "Gum ging !?"   

RoyaleM3 發表於 2013-7-24 12:01
C hing, change the plastic center shaft la

我覺得條膠軸味有必要換金屬住，等我用9T 轟多佢一輪先，我唔系乜都要金屬，膠都有膠好
而且而家要改好快車手腳先再諗其它

YSL 發表於 2013-7-24 12:17
我覺得條膠軸味有必要換金屬住，等我用9T 轟多佢一輪先，我唔系乜都要金屬，膠都有膠好
而且而家要改好快 ...

I see.  
Look forward to your further updates.
I haven't run mine yet.....bad weather.

今日裝多少少野 差唔多完成,再做少少調整可以試車,唔知行起上會同原裝有幾大分别呢

YSL 發表於 2013-7-24 23:15
今日裝多少少野 差唔多完成,再做少少調整可以試車,唔知行起上會同原裝有幾大分别呢 ...

師兄請問套手腳KWS有冇得買?

m05car 發表於 2013-7-25 20:59
師兄請問套手腳KWS有冇得買?

我系用 R-1 套手腳

YSL 發表於 2013-7-25 21:13
我系用 R-1 套手腳

師兄好有鬼才......

m05car 發表於 2013-7-25 22:40
師兄好有鬼才......

呢架系 TT-02

YSL 發表於 2013-7-25 22:55
呢架系 TT-02

睇得出帥兄好有心思去改...值得一

YSL 發表於 2013-7-25 21:13
我系用 R-1 套手腳

Ching, what to use to fit into the pin hole?

tsfai 發表於 2013-7-25 23:54
Ching, what to use to fit into the pin hole?

用TT-01E 下搖臂 穿PIN 個2粒膠的

YSL 發表於 2013-7-26 00:17
用TT-01E 下搖臂 穿PIN 個2粒膠的

Is TT 01 D type E 下搖臂 穿PIN 個2粒膠的

Kevin8933 發表於 2013-7-26 00:37
Is TT 01 D type E 下搖臂 穿PIN 個2粒膠的

我架 TT-01 系 E - R

http://www.tamiya.com/japan/prod ... _id=58450&col=6

TT 01都可以改?

limk2004 發表於 2013-7-26 01:02
TT 01都可以改?

我系話用 TT 01 舊件呢改架TT 02 姐

YSL 發表於 2013-7-25 22:55
呢架系 TT-02

這樣尾 ToeIn 會太少，雖要做一寬 Pin 位的尾碼。