(有片睇!! page 7) 2007 年- 我的新玩具 GT-01 Porsche 934

大家cut車殼時最好將車轆砂板條裙邊剪幼啲.
可參考之前真車或車盒圖圖片. 模型大寛了.

噚晚砌咗個波箱落架車架到喇.

Coming Sat 3:00pm 橋底有冇人試934呀?

又多咗位師兄買咗934

1. fyin
2. pliablewai
3. gibson
4. RCman
5. RC
6. skleejames
7. minimini

原帖由 fyin 於 2007-1-18 13:38 發表
Coming Sat 3:00pm 橋底有冇人試934呀?

Sat family day.....

原帖由 gibson 於 2007-1-20 01:01 發表



Sat family day.....

Don't worry! Just for test run with my fan sin, I just completed the chassis and make test run on tomorrow.
After the paint was arrived and everyone completed the body shell then will take a 934 party la.

原帖由 fyin 於 2007-1-20 00:59 發表
又多咗位師兄買咗934

1. fyin
2. pliablewai
3. gibson
4. RCman
5. RC
6. skleejames
7. minimini

大家千祈唔好忘記 post 自己嘅愛驅出嚟一齊分享吓.........

原帖由 <i>minimini</i> 於 2007-1-20 01:27 發表\


大家千祈唔好忘記 post 自己?愛驅出?一齊分享嚇.........\

\

昨晚有朋友出開KWS
叫佢幫我問有934專用油到未...............結果都係.............

今日下午我和Fyin會到橋底試車,有冇兄弟一齊, 最少有兩架934出現, 不過只是跑車架, 仍然等油噴殼.

just bought this decal today........my car can then be painted into orange color lu..........

Hi Bro Minimini,
Very nice decal, where did you bought from & how much? in HK or bid?
Hope to buy one la.

[ 本帖最後由 fyin 於 2007-1-23 00:25 編輯 ]

原帖由 minimini 於 2007-1-23 00:10 發表
just bought this decal today........my car can then be painted into orange color lu..........

Good stuff!!!

原帖由 fyin 於 2007-1-23 00:20 發表
Hi Bro Minimini,
Very nice decal, where did you bought from & how much? in HK or bid?
Hope to buy one la.

X2 !

Where did you buy it??

原帖由 minimini 於 2007-1-23 00:10 發表
just bought this decal today........my car can then be painted into orange color lu..........

So Lucky! 你就好喇買到這張貼紙. 我就只可scan張舊水貼.

原帖由 fyin 於 2007-1-23 11:34 發表



So Lucky! 你就好喇買到這張貼紙. 我就只可scan張舊水貼.

Still better than me, I have nothing.  Just finishted 60% of the chassis.  Very complicated.  Not a normal RC on road chassis..     Normally for me to finish a RC chassis, not more than 8 hours, but for this little guy, need more time...  

And I hate the plastic materials, a bit softer, so difficult to fix the screws....

Hi Bro Gibson,
Don't worry! be happy! Once you drive it on the track you must have serve.

原帖由 fyin 於 2007-1-24 00:48 發表
Hi Bro Gibson,
Don't worry! be happy! Once you drive it on the track you must have serve.

pretty close, pretty close to finish!!!!   The servo is a problem, finally I went to Wan Kee and bought the Tamiya special servo for this little guy, HKD190.   


And have to finish it tomorrow or weekend!!

原帖由 gibson 於 2007-1-24 01:26 發表




pretty close, pretty close to finish!!!!   The servo is a problem, finally I went to Wan Kee and bought the Tamiya special servo for this little guy, HKD190.   


And have to finish  ...

u can use hitec 85BB servo is fit for this car

Hi Bro,
I used hitec HS81, but need to cut & trim servo holder.
I think use tamiya tamtech servo was better. Just fit in as well.

One more 1/12 Tamtech 934 fans...hehe

1. fyin
2. pliablewai
3. gibson
4. RCman
5. RC
6. skleejames
7. minimini
8. buggy