Axial AE-2 電變調整設定有感 + 追加704/705膠防水應用 (updated)

艱得師兄咁有心機同人分享,又學到野thx

師兄:
我咁改完唔知散熱會唔會差咗?

尼件唔知要唔要做防水呢？

Thanks for the sharing!!!  Just saw this good post!!!  

bbfonghk 發表於 2014-6-2 21:22
師兄:
我咁改完唔知散熱會唔會差咗?

係會影響散熱的, 但係未必會有太大問題. 是乎你部車setup 對電流既要求有幾大. 我行35t摩打21t 摩打齒原裝大減部車點行隻電變都冇咩點發熱. 不過我用外置bec, 電變發熱量都會變小.

而你另一幅圖應該係車燈控制板, 都要做埋放水, 都係剪開熱縮通, 包704 (留返插頭位)

Please del.....

師兄，我剛抽出電子野準備做防水。請問除左 servo, esc, receiver box, 開關制同 dc 馬達是否都要防水?唔好意思，小弟是新身呢!

elton2xxx 發表於 2014-6-3 22:42
師兄，我剛抽出電子野準備做防水。請問除左 servo, esc, receiver box, 開關制同 dc 馬達是否都要防水?唔好 ...

motor 同電都唔使防, 開關唔一定要, 當然可以就做

Thanks ricksonchow ching!!!  I hear you!   

請問那車呔排氣孔要封嗎？

cyt2011 發表於 2014-6-4 00:44
請問那車呔排氣孔要封嗎？

我會建議封埋佢, 因為入左水D 海綿會腐爛, 如果改左金屬鈴, 可以響加重圈上面包膠紙

ricksonchow兄;唔知AE2過熱係咪會自動cut電呢?

bbfonghk 發表於 2014-6-4 11:20
ricksonchow兄;唔知AE2過熱係咪會自動cut電呢?

我唔太sure, 不過你預佢冇穏陣D, 同埋你平時玩開都會知佢大概咩溫度左右, 未加防水之前暖暖地唔會有咩問題

ricksonchow 發表於 2014-6-4 11:55
我唔太sure, 不過你預佢冇穏陣D, 同埋你平時玩開都會知佢大概咩溫度左右, 未加防水之前暖暖地唔會有咩問 ...

我隻AE2仲未正式玩過 :-)

bbfonghk 發表於 2014-6-4 12:30
我隻AE2仲未正式玩過 :-)

35T 搭原裝齒冇問題

Good wor, can I buy those 704/705 stuff from SSP etc?  

We like to use "plasti dip" here, but the can one will dry up very fast, spray one is not thick enough.... Cheap to buy in USA for $6, but $25 in Canada.....


By the way, why not using Castle Link to program the esc, very easy..

965 發表於 2014-6-4 15:10
Good wor, can I buy those 704/705 stuff from SSP etc?  

We like to use "plasti dip" here, but the c ...

I am not sure if you can find them in SSP but as I remembered they are available on yahoo acution. I was using plasti dip (spray) but the out come was not satisfied and now I am stuck to this 704 method which I think it can out perform plasti dip as they are clean and tidy. Also this sealant is made for that!

Of course I can program it using castle link but the problem is I don't have one. May be I need to get one as I have to program my castle bec output voltage

I have noticed some c hing are using those 704/705, just wonder where to buy them..., thx?

965 發表於 2014-6-4 15:58
I have noticed some c hing are using those 704/705, just wonder where to buy them..., thx?

Not sure if you can find them in Canada. May be only on ebay. http://www.ebay.com/itm/New-704- ... -Glue-/191164555416

Folks in US or Canada; here you go. Amazon..ebay...
Conformal coating >>MG Chemicals 419b
http://sra-solder.com/product.ph ... I4L4CFUlqfgodUFMA0A
AND
Corrision X
http://www.corrosionx.com/corrosionx.html
I am too lazy and i use plastic dip...but all should work