VIPER VTX8 SETTING 分享 - 香港代理提供的"起鏢位"

小弟最近在LALI認識唔少新朋友 , 當中有不少朋友用VIPER的VTX8 , R65的原廠設定的確是力的表現 , 本人覺得太"牛B"了

我都只是剛開始用了一星期左右 , 坦白講VIPER的設定的確是好處也是壞處 , 新朋友一定會有點頭痛 , 因為太細緻了 , 同時表示的方式大多是數字單位化 , 當中更是可調的空間相當大 , 不了解的一定試到暈底 , 明白的話就非常好用 , 要是胡亂設定的話 , 便有可能誤會ESC是否有問題 , 其實就是空間大 , SET錯的機會更大 , 所以話套餐也有好處的 , 看的就是你是否想要最合心水的 , 這定必是自己煮的了


下面的設定是基於原廠設定後,須要更改的部份,沒有提到的,就不用更改,現在這設定是源於香港代理提供的LALI場地的"起鏢位" , 小弟的就在()內 , 歡迎與各位朋友交流交流 , 有問題的話 , 請提點一下小弟


Class: 1/8 EP Buggy
Car: Mugen MBX7(mcp layout)
BATT:reedy 4100 shorty 65C
ESC: VIPER VTX8
Motor: Tekin new T8 1900kv

VTX8 SETTING 分享
SOFTWARE:R65
RUN MODE: Practise or Blinky Mode (Practise玩場地都是有後波方便點 , 何況R65可以無限BRAKE之後才有後波)
Motor Type : 4Polo
Battery Protection : Lowest or 7.4V (7.4)
Motor Proctect : Off
ESC Protect : 260F

Throttle Freq :12000 to 19000 (19000)
Punch:100
BEC: 8V

REV POWER: (25%)

Brake Freq 8000 to 9600 (9600)
Brake S: 100

Thx, sorry to ask, R65 is new firmware? Pretty nice idea to run two shorty on side, could you please share more photos and detail how it mount?

I am new user for the VTX8, correct me if I am wrong, if I want to add timing, I need race mode, but no reverse, and if I want reverse, I can't add timing / boost, and stick with pratrice mode?

I hv the prologue, but not the Viper PC link, can't update firmware, however, right now, I can set the BEC up to 8v, bit Viper claims only up to 7v, I worry about with new firmware, can only go up to 7v.


Thx...

965 發表於 2014-6-9 13:19
Thx, sorry to ask, R65 is new firmware? Pretty nice idea to run two shorty on side, could you please ...

Thx, sorry to ask, R65 is new firmware? Pretty nice idea to run two shorty on side, could you please share more photos and detail how it mount? I am new user for the VTX8, correct me if I am wrong, if I want to add timing, I need race mode, but no reverse, and if I want reverse, I can't add timing / boost, and stick with pratrice mode? I hv the prologue, but not the Viper PC link, can't update firmware, however, right now, I can set the BEC up to 8v, bit Viper claims only up to 7v, I worry about with new firmware, can only go up to 7v.

I get my vtx8 at HEC 鴻聲模型 and they help me to update 65 firmware (another place is PYC. The room of TEAM VIPER HK)


If u want run reverse as the esc having timing/boost setting, pls use Pratrice Mode (pls notes u must set the reverse power level yourself)




R65 can set bec as 8V too. If u run it as 4 cells because u having more V on hand (incase of 2 cells max 7.4V as well because the esc no need to push it up)

Thx, but when I selected practice  mode, it said "motor power is not available...."



8V bec is awesome! Can hv some fun with HV servo... I want that for my RX8 ... But don't want to get gen II just because of that... So ..give Viper a try!

965 發表於 2014-6-9 14:22
Thx, but when I selected practice  mode, it said "motor power is not available...."

May be u update the 65 frist and try it again because i m start as 65.
Which motor using now?

I hvn't hook it up yet ..

Don't have PC link to update ..

剛剛了解過，原來R65是測試中的板本，沒有A64那麼完整 , 例如一些預設的套餐 , 暫時A64是正式板的最新板本 , 只有VIPER代理才有 , 不怪得英文字怪怪的. 不好意思各位朋友 , 但設定是一樣WORK的 , 因為在A64時我都是行這個"起鏢位"去微調的
A64預設套餐的資料,請看下列連接,看你的車子類似選定後再微調
http://www.viper-rc.com/downloads/A64%20Release%20Note.pdf


小小貼士給新用家 , Throttle/ Brake 的數值超越大 , 意思即是越溫柔越細膩 , 數值超越小 , 意思即是越粗獷越強勢 , 其他請參照說明書

thx you thx you ..

My VTX10 already made me headache ...  end up stick with Tekin/HobbyWing/Castle .. more simple ..    

May be I should buy a Viper PC link from HK ..  if you know how much?

965 發表於 2014-6-11 15:12
thx you thx you ..

My VTX10 already made me headache ...  end up stick with Tekin/HobbyWing/Castle ...

I DON'T have this also, May be u can ask HEC