Hummer H2 SUT

原帖由 宏 於 2006-2-20 12:24 AM 發表


That is 1/8 scale,mine is 1/10 scale 190mm size, Wheel Base 260cm
http://www.rcworld.ch/neueprojekte.asp?id=1147

Thx!! How much $?

Including the rear mirror? (the pic on AMAT's and your link w/o rear mirror)

原帖由 txzmxn 於 2006-2-20 00:29 發表


Thx!! How much $?

Including the rear mirror? (the pic on AMAT's and your link w/o rear mirror)

紅星$150, 見存就好似有...但要$260
其他地方唔知有冇...

原帖由 mikewu 於 2006-2-20 00:28 發表


hehehehe....  I have 2....  bought it at the same store... I can sell you one..... (just kidding) I am thinking to paint one for drifting..  But it's strange for a Hummer drift.....  Still t ...

哈....唔係far...hummer玩dirft...
真係幾 strange ...

原帖由 txzmxn 於 2006-2-20 00:29 發表


Thx!! How much $?

Including the rear mirror? (the pic on AMAT's and your link w/o rear mirror)

冇倒後鏡的.

佢好似有出幾個VERSION.
不過呢隻SUT版呢,就係190MM TOURING車架用O既VERSION嚟.

我宜家都打算改佢落TA02到,不過我果個係TA01底,要換臂先用到,唔係輪距唔O岩.

wonderful printing
how much of the ''kyosho rally呔"

原帖由 宏 於 2006-2-20 02:00 AM 發表

紅星$150, 見存就好似有...但要$260
其他地方唔知有冇...

原帖由 天照 於 2006-2-20 12:39 PM 發表

冇倒後鏡的.

佢好似有出幾個VERSION.
不過呢隻SUT版呢,就係190MM TOURING車架用O既VERSION嚟.

我宜家都打算改佢落TA02到,不過我果個係TA01底,要換臂先用到,唔係輪距唔O岩.

Thx both!
But how come 宏's rear mirror? buy seperately?

原帖由 txzmxn 於 2006-2-20 21:43 發表




Thx both!
But how come 宏's rear mirror? buy seperately?

相信係用舊HUMMER個鏡裝上去~!哈!

原帖由 AMAT 於 2006-2-20 21:45 發表


相信係用舊HUMMER個鏡裝上去~!哈!

冇錯~
屋企冇啦啦有對舊HUMMER鏡咪裝上去囉~

原帖由 天照 於 2006-2-20 12:39 發表


冇倒後鏡的.

佢好似有出幾個VERSION.
不過呢隻SUT版呢,就係190MM TOURING車架用O既VERSION?.

我宜家都打算改佢落TA02到,不過我果個係TA01底,要換臂先用到,唔係輪距唔O岩.

brother...

as i know...the wheelbase of ta01 and ta02 is almost the same......ta02 just move the CG a bit towards the front part....the middle part shorter.....the rear sup. arm point to the rear....so u will see that the rear sup. arm seem in different direction compare with ta01.......as i'm not quite sure the wheelbase of your ta01(the hummer one, right!!??)....maybe it's longer than the standard ta01.....maybe u go and check check la!!

原帖由 monkichi0210 於 2006-2-21 10:24 發表


brother...

as i know...the wheelbase of ta01 and ta02 is almost the same......ta02 just move the CG a bit towards the front part....the middle part shorter.....the rear sup. arm point to the ...

我果O架車咗囉~!哈!
所以要改~!

原帖由 宏 於 2006-2-19 09:04 PM 發表
前後加後用左4日先搞掂...要mask既野多到嘔...
噴完都唔太捨得玩~

架車噴得好靚，完完全全沒有"曬"咗個 Shell。越睇越正！

條呔重有無得買呀??我有架TA01都想.....

原帖由 宏 於 2006-2-19 21:04 發表
前後加後用左4日先搞掂...要mask既野多到嘔...
噴完都唔太捨得玩~

宏;

Can fit HPI MT-2 (big foot), thanks

原帖由 pantherjovi 於 2006-2-21 11:43 發表
條呔重有無得買呀??我有架TA01都想.....

有...kws有幾間都見到有得賣...

原帖由 Oakfield 於 2006-2-21 11:52 發表


宏;

Can fit HPI MT-2 (big foot), thanks

我唔清楚mt-2個wb係幾多...如果係260mm就fit了~