F103GT 3Racing & Tamiya Cross Over

My F103GT with some option from both Tamiya and 3RAcing,

THe ideal will still be going for Tamiya parts, those one that were not produced by Tamiya will go with 3Racing....

Thanks for watching

我部f103gt 唔係係咪係街玩得多.......個原裝大齒輪有d牙都崩左......點算.....??

原帖由 rk2 於 2007-3-6 17:39 發表


So this LED is a part of the Novark smart stop ?

yes...included..a very bright LED too~

原帖由 jpmontoya2 於 2007-3-6 15:31 發表


When battery starts to go down and approaches the critical value of 6.25 V (if i remember correctly), the Blue LED will flash...indicating you are low on battery and advise you to stop playing. ...

So this LED is a part of the Novark smart stop ?

原帖由 orange00 於 2007-3-6 16:17 發表

相信servo會唔夠電

我隻 servo 係 6V ,我諗應該夠.

原帖由 pat1111 於 2007-3-6 16:11 發表



如果張粒 藍色 LED ,改做4 粒死火燈放車殼到.好唔好呢

相信servo會唔夠電

原帖由 jpmontoya2 於 2007-3-6 16:04 發表

BINGO~~~~

如果張粒 藍色 LED ,改做4 粒死火燈放車殼到.好唔好呢

原帖由 orange00 於 2007-3-6 16:03 發表

And thanks Novak product designer, the steering control still availabe after motor power cut off.

this call smart stop ma only stop motor not stop the steering

原帖由 pat1111 於 2007-3-6 15:58 發表



明白點攪,我會係ecs 去電個T plug 加多一個細o既plug.個plug 去 smart stop 20G 紅黑線度.用lipo 就用 smart stop.唔用lipo 就 unplug .
當唔用smart stop 時 esc 條 紅黑白線去番接收.

BINGO~~~~

原帖由 pat1111 於 2007-3-6 15:47 發表



icic

And thanks Novak product designer, the steering control still availabe after motor power cut off.

原帖由 jpmontoya2 於 2007-3-6 15:49 發表


I do it this way,
I use a seperate connector between the Lipo batteries to the ESC. At this seperatte connector add another linakge for the smart stop.

Then the smart stop can be remove o ...

明白點攪,我會係ecs 去電個T plug 加多一個細o既plug.個plug 去 smart stop 20G 紅黑線度.用lipo 就用 smart stop.唔用lipo 就 unplug .
當唔用smart stop 時 esc 條 紅黑白線去番接收.

原帖由 pat1111 於 2007-3-6 15:44 發表



又學到野喇...Thanks

之到點攪攪可以用二種電

I do it this way,
I use a seperate connector between the Lipo batteries to the ESC. At this seperatte connector add another linakge for the smart stop.

Then the smart stop can be remove or replug whenever u are needed~

If you are uncertain, i maybe able to take another pic tonite on that subject~

原帖由 jpmontoya2 於 2007-3-6 15:39 發表


No..it will flash.....but the car simply stops....no power to the motor!

icic

原帖由 jpmontoya2 於 2007-3-6 15:18 發表



Umm..i have not try wor......becasue of the above reason...thats why u see my smart stop is solder as a seperate unit. I have batery flug and T-plug to hook it up. So if i am using NiMH i ca ...

又學到野喇...Thanks

之到點攪攪可以用二種電

原帖由 pat1111 於 2007-3-6 15:38 發表



當電壓低會閃藍燈,再低去度6.25V 會長著

No..it will flash.....but the car simply stops....no power to the motor!

原帖由 rk2 於 2007-3-6 15:23 發表
車上 粒 led 有咩用架 ?

當電壓低會閃藍燈,再低去度6.25V 會長著

原帖由 rk2 於 2007-3-6 15:23 發表
車上 粒 led 有咩用架 ?

When battery starts to go down and approaches the critical value of 6.25 V (if i remember correctly), the Blue LED will flash...indicating you are low on battery and advise you to stop playing.

However if you keep playing while the LED flashes, when the power drops below 6.25V, the smart stop will stop the car only leaving sterring function......

All that is doing is to pretect the Lipo being over discharge~

車上 粒 led 有咩用架 ?

原帖由 pat1111 於 2007-3-6 15:16 發表
jpmontoya2 師

有無試過 ,個 smart stop 用番 Ni Mh 電?得唔得呢?
因個 smart stop 我以捍左去 ESC 度,當粒 lipo 無電時,想用ni mh 電玩.

Umm..i have not try wor......becasue of the above reason...thats why u see my smart stop is solder as a seperate unit. I have batery flug and T-plug to hook it up. So if i am using NiMH i can take the smart stop away easily..

Can any other brother give him a help?

jpmontoya2 師

有無試過 ,個 smart stop 用番 Ni Mh 電?得唔得呢?
因個 smart stop 我以捍左去 ESC 度,當粒 lipo 無電時,想用ni mh 電玩.