F103GT 3Racing & Tamiya Cross Over

My F103GT with some option from both Tamiya and 3RAcing,

THe ideal will still be going for Tamiya parts, those one that were not produced by Tamiya will go with 3Racing....

Thanks for watching

原帖由 觀星是答案 於 2007-1-16 00:47 發表
成個車尾用晒 3Racing 金屬座吧 !

我以前架 F103GT ...

No la...i like the rear abit lighter...so far my car runs great..i have no intention to change to alloy at the rear la......:-)

原帖由 S20002330 於 2007-1-16 10:09 發表
個個架車都好靚呵
我想問問lock個轆個粒藍色大六角在那裡找的，我係"喂高"只係見到金色同紫色
還有我想問問3racing個頭轉向杯個高度係咪矮過原裝的

頭轉向杯 is same as Tamiya~

My F103GT hopped up with some Lipo la~~~..

原帖由 rk2 於 2007-3-6 09:06 發表
beautiful ! ~~ with Tamiya racing towel

Thank you ~~

原帖由 S20002330 於 2007-3-6 09:11 發表

請問個電上面個塊電子板係咩來嫁
你架車改得好靚

That is a NOvak Smart Stop.....it helps to detect the voltage remains on the Lipo. When the voltage drops to a critical value, the Smart Stop will flash Blue...and if you keep running, the Smart Stop will stop the car to pretect the Lipo~

原帖由 rk2 於 2007-3-6 13:07 發表
NOvak Smart Stop -- EXPENSIVE OR NOT ?

around $240 la~

Check out with your local hobby shop~

原帖由 pat1111 於 2007-3-6 15:16 發表
jpmontoya2 師

有無試過 ,個 smart stop 用番 Ni Mh 電?得唔得呢?
因個 smart stop 我以捍左去 ESC 度,當粒 lipo 無電時,想用ni mh 電玩.

Umm..i have not try wor......becasue of the above reason...thats why u see my smart stop is solder as a seperate unit. I have batery flug and T-plug to hook it up. So if i am using NiMH i can take the smart stop away easily..

Can any other brother give him a help?

原帖由 rk2 於 2007-3-6 15:23 發表
車上 粒 led 有咩用架 ?

When battery starts to go down and approaches the critical value of 6.25 V (if i remember correctly), the Blue LED will flash...indicating you are low on battery and advise you to stop playing.

However if you keep playing while the LED flashes, when the power drops below 6.25V, the smart stop will stop the car only leaving sterring function......

All that is doing is to pretect the Lipo being over discharge~

原帖由 pat1111 於 2007-3-6 15:38 發表



當電壓低會閃藍燈,再低去度6.25V 會長著

No..it will flash.....but the car simply stops....no power to the motor!

原帖由 pat1111 於 2007-3-6 15:44 發表



又學到野喇...Thanks

之到點攪攪可以用二種電

I do it this way,
I use a seperate connector between the Lipo batteries to the ESC. At this seperatte connector add another linakge for the smart stop.

Then the smart stop can be remove or replug whenever u are needed~

If you are uncertain, i maybe able to take another pic tonite on that subject~

原帖由 pat1111 於 2007-3-6 15:58 發表



明白點攪,我會係ecs 去電個T plug 加多一個細o既plug.個plug 去 smart stop 20G 紅黑線度.用lipo 就用 smart stop.唔用lipo 就 unplug .
當唔用smart stop 時 esc 條 紅黑白線去番接收.

BINGO~~~~

原帖由 rk2 於 2007-3-6 17:39 發表


So this LED is a part of the Novark smart stop ?

yes...included..a very bright LED too~