1:8 GT & 電平8 玩家專區

Shared a video I took yesterday in Singapore track.
Replaced spur to 41t, and running with a gas power GT8 in last 2 laps.
http://www.youtube.com/watch?v=gfYQ22NSGZ4
Speed is much better than previous run with original spur. Feel that I can increase pinion by 1 to 2 teeth.

ernestf 發表於 2013-5-19 13:26

                               
登錄/註冊後可看大圖

Shared a video I took yesterday in Singapore track.
Replaced spur to 41t, and running with a gas pow ...

good

kennethcheng 發表於 2013-5-19 11:27

                               
登錄/註冊後可看大圖

Hi PYC,

Then Viper is very funny, i went to HUng Sing and Viper's website, they all said must chan ...

Hi,

A picture more than thousand word.  

I apply the setting from Viper's web site which indicate the setting for GT.   It just run for one lap and stop in the middel of the TRC.  And then smoking comming out.  Lots of Ching saw that, what a suck ESC.

May be Viper or the shop will challenge my car's setting is making that.  The fact is, I change to HobbyWing's ESC, after the burning of Viper.  Exactly the same setting on the GT8, no a single screw change.  I can run very comfort and FAST.  What a shame for Viper.  May be Chinese is the king

My car normally run with Tekin RX8 for more than 1/2 year with more extreme setting like 41/22 and NO any issue.  Just may be it getting old and soem jittering during run that making me consider to change.

If Viper say it is so powerful, why don't load some more friendly setting by default?  Or just put some immature product to the market and ask player to pray?

I tried RX8, HW, Crowcrow and Viper.  The previous third is good to run, easy to setup.  The most powerful is Viper ON BURNING!!!!!!!

GOOD LUCY and try to avoid from it!!!!

有冇Ching試過換快齒後應該用什麼齒比？我未換之前用42／18，150A及2750KV都冇事。

DLLL 發表於 2013-5-19 19:01

                               
登錄/註冊後可看大圖

有冇Ching試過換快齒後應該用什麼齒比？我未換之前用42／18，150A及2750KV都冇事。 ...

師兄， 我尋日用同你一樣， 快呀。42／17。 HW 同812。17呀沒問題。18呀好快。 同一setting, 17呀， Viper 燒左。相可看上面個post.

benz1850 發表於 2013-5-19 19:13

                               
登錄/註冊後可看大圖

師兄， 我尋日用同你一樣， 快呀。42／17。 HW 同812。17呀沒問題。18呀好快。 同一setting, 17呀， Vipe ...

我而家未試好，昨日在JV行45／16，覺得好似未換快齒前行42／18還快d

DLLL 發表於 2013-5-19 19:26

                               
登錄/註冊後可看大圖

我而家未試好，昨日在JV行45／16，覺得好似未換快齒前行42／18還快d

JV行45／16
有冇check 溫度係咪低左?

可能我之前用2把風扇40mm&50mm外置11V吹摩打，但而家只用40mm吹摩打50mm吹電變，所以摩打兩個做法都係約70度

好似45/16穩陣d 冇咁易過熱

0433433 發表於 2013-5-19 20:50

                               
登錄/註冊後可看大圖

好似45/16穩陣d 冇咁易過熱

係呀！不過會慢d啦

試下18同45,反正你有

tungming508 發表於 2013-5-23 20:28

                               
登錄/註冊後可看大圖

試下18同45,反正你有

其實45／16都好熱

咁唯有等下Tekin RX8第二代啦

Just bought Viper and SP 2750KV motor

good luck, me and my friend burn 3 of them already.....

祝君好運了

不用了，可能firmware 出問題，對不到控，廠跟進中，不过要讚吓林sir佢已盡咗力幫手

ed003 發表於 2013-5-28 15:09

                               
登錄/註冊後可看大圖

Just bought Viper and SP 2750KV motor

等你好燒息。。。。。。

ed003 發表於 2013-5-28 22:08

                               
登錄/註冊後可看大圖

不用了，可能firmware 出問題，對不到控，廠跟進中，不过要讚吓林sir佢已盡咗力幫手 ...

嘩，獲獲新奇獲獲金。Viper 真好野。

原来係條sensor cable 唔work 仲搞咗咁耐