Avante Road Test (DF03 owner/buyer must read)

Mike, Thanks for the tips about adding spacer to the pin. I will work on mine tonight.

原帖由 vr2uhu 於 2007-6-13 12:22 發表

                               
登錄/註冊後可看大圖

will cost u 100 in chong sing....3 racxx product... i got one....the one and the only one blue metal on my car.....

Thanks bros, why I did not notice this metal cup!!  

HKD100, I can buy a RC car with HKD5 change!!

原帖由 AMAT 於 2007-6-13 12:48 發表

                               
登錄/註冊後可看大圖

我砌果時都已經發現到有呢個問題,所以我前後臂PIN都已經落晒O的SPACER落去~

My rear doesn't seem to have the same problem bor....?   Just the front king pin....

原帖由 007 於 2007-6-13 12:50 發表

                               
登錄/註冊後可看大圖

Mike, Thanks for the tips about adding spacer to the pin. I will work on mine tonight.

No problem..  That's why I put this post on top highlighted with Red....  

原帖由 gibson 於 2007-6-13 12:55 發表

                               
登錄/註冊後可看大圖

HKD100, I can buy a RC car with HKD5 change!!

A piece of crap don't even have any springs or shocks..............    You should start a new post about your RC boys....  

原帖由 mikewu 於 2007-6-13 12:56 發表

                               
登錄/註冊後可看大圖

My rear doesn't seem to have the same problem bor....?   Just the front king pin....

橫掂都係喇,咪落埋去囉~!哈!

原帖由 mikewu 於 2007-6-13 10:50 發表

                               
登錄/註冊後可看大圖

For every DF03 owner, be sure to add spacers on your front king pin.  It's a designing failure as the king pin might move towards the steering and hit the steering rods.  And here is my DF03 Dark ...

Mike, what is the size of your spacer, 2.5mm or 3mm?

貼我架出黎先!!!

原帖由 vr2xvh 於 2007-6-13 23:17 發表

                               
登錄/註冊後可看大圖

貼我架出黎先!!!

vr2xvh, be careful with your ESC +- cables. They will touch the propellar.

原帖由 007 於 2007-6-14 10:38 發表

                               
登錄/註冊後可看大圖

vr2xvh, be careful with your ESC +- cables. They will touch the propellar.

oh, thanks for your remind.....let me reverse the direction of battery cable

valcro(<<-----dun know how to spell) added to the body....no clips are requited now

and it can keep clean inside the chassis...

似乎好多 bros 都將嗰 3 支 heat-sink 向出面裝喎.....

原帖由 vr2uhu 於 2007-6-14 23:37 發表

                               
登錄/註冊後可看大圖

valcro(

I use this one!

Motor:   
Tamiya 23T RZ

ESC:   
TC2

Servo:  
bluebird 616mg+hs    0.12s    9.2kg/cm

Damper:  
original

Modifications:
1) Motor heat sink (Tamiya)
2) central One way bearing (Tamiya)
3) Slipper Clutch (Tamiya)
4) Universial Joints front (tamiya df-02)
5) front one way (Tamiya)


Impression:
After 15-minute run, the tamiya 23T RZ is fcuking hot. Therefore, a motor heat sink is a MUST.
Tamiya DF-02 universial joints perfectly fit DF-03 (front, as I am still using the original one at the rear). If you are unable to get a 3 racing universial joint, you may use a df-02 instead. The rear shock tower is terribly soft!!!

I don't understand why my car always oversteering when it is decelerating, but once it accelerates, it becomes understeering.....

原帖由 vr2xvh 於 2007-6-16 10:42 發表

                               
登錄/註冊後可看大圖

Motor:   
Tamiya 23T RZ

ESC:   
TC2

Servo:  
bluebird 616mg+hs    0.12s    9.2kg/cm

Damper:  
original

Modifications:
1) Motor heat sink (Tamiya)
2) central One way bearing (Tam ...

"I don't understand why my car always oversteering when it is decelerating, but once it accelerates, it becomes understeering....."

It is normal wor. It is always like this for my other cars.

原帖由 vr2xvh 於 2007-6-16 10:42 發表

                               
登錄/註冊後可看大圖

I don't understand why my car always oversteering when it is decelerating, but once it accelerates, it becomes understeering.....

This means your front & mid one way is working well....
can be faster out of the corner..

sunli兄，Thank you u 教我齒比，我決定買6.5R試試

[ 本帖最後由 owl 於 2007-9-29 15:02 編輯 ]

原帖由 owl 於 2007-6-16 18:06 發表

                               
登錄/註冊後可看大圖

sunli兄，Thank you u 教我齒比，我決定買6.5R試試

Hope this is useful for you....

[ 本帖最後由 SunLi 於 2007-6-16 19:50 編輯 ]